windows\centos\suse\rhel的ZABBIX_agent安装脚本

# This is a configuration file for Zabbix agent service (Windows) # To get more information about Zabbix, visit http://www.zabbix.com ############ GENERAL PARAMETERS ################# ### Option: LogType # Specifies where log messages are written to: # system - Windows event log # file - file specified with LogFile parameter # console - standard output # # Mandatory: no # Default: # LogType=file ### Option: LogFile # Log file name for LogType 'file' parameter. # # Mandatory: no # Default: # LogFile= LogFile=c:\zabbix\zabbix_agentd.log ### Option: LogFileSize # Maximum size of log file in MB. # 0 - disable automatic log rotation. # # Mandatory: no # Range: 0-1024 # Default: # LogFileSize=1 ### Option: DebugLevel # Specifies debug level: # 0 - basic information about starting and stopping of Zabbix processes # 1 - critical information # 2 - error information # 3 - warnings # 4 - for debugging (produces lots of information) # 5 - extended debugging (produces even more information) # # Mandatory: no # Range: 0-5 # Default: # DebugLevel=3 ### Option: SourceIP # Source IP address for outgoing connections. # # Mandatory: no # Default: # SourceIP= ### Option: EnableRemoteCommands # Whether remote commands from Zabbix server are allowed. # 0 - not allowed # 1 - allowed # # Mandatory: no # Default: # EnableRemoteCommands=0 ### Option: LogRemoteCommands # Enable logging of executed shell commands as warnings. # 0 - disabled # 1 - enabled # # Mandatory: no # Default: # LogRemoteCommands=0 ##### Passive checks related ### Option: Server # List of comma delimited IP addresses, optionally in CIDR notation, or DNS names of Zabbix servers and Zabbix proxies. # Incoming connections will be accepted only from the hosts listed here. # If IPv6 support is enabled then '127.0.0.1', '::127.0.0.1', '::ffff:127.0.0.1' are treated equally and '::/0' will allow any IPv4 or IPv6 address. # '0.0.0.0/0' can be used to allow any IPv4 address. # Example: Server=127.0.0.1,192.168.1.0/24,::1,2001:db8::/32,zabbix.domain # # Mandatory: yes, if StartAgents is not explicitly set to 0 # Default: # Server= Server=127.0.0.1 ### Option: ListenPort # Agent will listen on this port for connections from the server. # # Mandatory: no # Range: 1024-32767 # Default: # ListenPort=10050 ### Option: ListenIP # List of comma delimited IP addresses that the agent should listen on. # First IP address is sent to Zabbix server if connecting to it to retrieve list of active checks. # # Mandatory: no # Default: # ListenIP=0.0.0.0 ### Option: StartAgents # Number of pre-forked instances of zabbix_agentd that process passive checks. # If set to 0, disables passive checks and the agent will not listen on any TCP port. # # Mandatory: no # Range: 0-100 # Default: # StartAgents=3 ##### Active checks related ### Option: ServerActive # List of comma delimited IP:port (or DNS name:port) pairs of Zabbix servers and Zabbix proxies for active checks. # If port is not specified, default port is used. # IPv6 addresses must be enclosed in square brackets if port for that host is specified. # If port is not specified, square brackets for IPv6 addresses are optional. # If this parameter is not specified, active checks are disabled. # Example: ServerActive=127.0.0.1:20051,zabbix.domain,[::1]:30051,::1,[12fc::1] # # Mandatory: no # Default: # ServerActive= ServerActive=127.0.0.1 ### Option: Hostname # Unique, case sensitive hostname. # Required for active checks and must match hostname as configured on the server. # Value is acquired from HostnameItem if undefined. # # Mandatory: no # Default: # Hostname= Hostname=ATWZYZQ ### Option: HostnameItem # Item used for generating Hostname if it is undefined. Ignored if Hostname is defined. # Does not support UserParameters or aliases. # # Mandatory: no # Default: # HostnameItem=system.hostname ### Option: HostMetadata # Optional parameter that defines host metadata. # Host metadata is used at host auto-registration process. # An agent will issue an error and not start if the value is over limit of 255 characters. # If not defined, value will be acquired from HostMetadataItem. # # Mandatory: no # Range: 0-255 characters # Default: # HostMetadata= ### Option: HostMetadataItem # Optional parameter that defines an item used for getting host metadata. # Host metadata is used at host auto-registration process. # During an auto-registration request an agent will log a warning message if # the value returned by specified item is over limit of 255 characters. # This option is only used when HostMetadata is not defined. # # Mandatory: no # Default: # HostMetadataItem= ### Option: RefreshActiveChecks # How often list of active checks is refreshed, in seconds. # # Mandatory: no # Range: 60-3600 # Default: # RefreshActiveChecks=120 ### Option: BufferSend # Do not keep data longer than N seconds in buffer. # # Mandatory: no # Range: 1-3600 # Default: # BufferSend=5 ### Option: BufferSize # Maximum number of values in a memory buffer. The agent will send # all collected data to Zabbix server or Proxy if the buffer is full. # # Mandatory: no # Range: 2-65535 # Default: # BufferSize=100 ### Option: MaxLinesPerSecond # Maximum number of new lines the agent will send per second to Zabbix Server # or Proxy processing 'log', 'logrt' and 'eventlog' active checks. # The provided value will be overridden by the parameter 'maxlines', # provided in 'log', 'logrt' or 'eventlog' item keys. # # Mandatory: no # Range: 1-1000 # Default: # MaxLinesPerSecond=20 ############ ADVANCED PARAMETERS ################# ### Option: Alias # Sets an alias for an item key. It can be used to substitute long and complex item key with a smaller and simpler one. # Multiple Alias parameters may be present. Multiple parameters with the same Alias key are not allowed. # Different Alias keys may reference the same item key. # For example, to retrieve paging file usage in percents from the server: # Alias=pg_usage:perf_counter[\Paging File(_Total)\% Usage] # Now shorthand key pg_usage may be used to retrieve data. # Aliases can be used in HostMetadataItem but not in HostnameItem or PerfCounter parameters. # # Mandatory: no # Range: # Default: ### Option: Timeout # Spend no more than Timeout seconds on processing. # # Mandatory: no # Range: 1-30 # Default: # Timeout=3 ### Option: PerfCounter # Syntax: <parameter_name>,"<perf_counter_path>",<period> # Defines new parameter <parameter_name> which is an average value for system performance counter <perf_counter_path> for the specified time period <period> (in seconds). # For example, if you wish to receive average number of processor interrupts per second for last minute, you can define new parameter "interrupts" as following: # PerfCounter = interrupts,"\Processor(0)\Interrupts/sec",60 # Please note double quotes around performance counter path. # Samples for calculating average value will be taken every second. # You may run "typeperf -qx" to get list of all performance counters available in Windows. # # Mandatory: no # Range: # Default: ### Option: Include # You may include individual files in the configuration file. # # Mandatory: no # Default: # Include= # Include=c:\zabbix\zabbix_agentd.userparams.conf # Include=c:\zabbix\zabbix_agentd.conf.d\ # Include=c:\zabbix\zabbix_agentd.conf.d\*.conf ####### USER-DEFINED MONITORED PARAMETERS ####### ### Option: UnsafeUserParameters # Allow all characters to be passed in arguments to user-defined parameters. # The following characters are not allowed: # \ ' " ` * ? [ ] { } ~ $ ! & ; ( ) < > | # @ # Additionally, newline characters are not allowed. # 0 - do not allow # 1 - allow # # Mandatory: no # Range: 0-1 # Default: # UnsafeUser