================================
Welcome to Electronics Workbench
================================
The Release Notes contain important information that was
received too late to be included in the written documentation.
They can be found in the online help. To view the release
notes, start Electronics Workbench and choose Release Notes
from the Help menu.
Below is further information which was too late to be included
in the online Help.
================================================================
Parser Errors Tab
A new tab has been added to the Analysis Graphs Window, called
"Parser Errors". The tab appears only if errors occur during
the parsing of a subcircuit netlist model. (Note: Parsing
occurs after you start a simulation or analysis.)
Most of the errors appearing in this list are only warnings.
They simply notify the user of syntax in a netlist which is
unsupported by Electronics Workbench.
================================================================
Electronics Workbench User's Guide Corrections
Page 5-2 - The circuit under Step 1 shows the first connection
of the word generator connected to connector "S" and the second
connection of the word generator connected to connector "R".
This is reversed. The first connection of the word generator
should be connected to connector "R" and the second to
connector "S".
Page 5-4 - The second point under Step 3 should state "Change
the frequency to 1 MHz".
Page 5-5 - The circuit under Step 1 shows the first connection
of the word generator connected to connector "S" and the second
connection of the word generator connected to connector "R".
This is reversed. The first connection of the word generator
should be connected to connector "R" and the second to
connector "S".
The procedure for setting the logic analyzer under Step 1 is no
longer correct as the logic analyzer was revised after the
printing of the User's Guide and Technical Reference.
The new procedure for setting the Logic Analyzer is as follows:
1. Set the frequency of the word generator to 1 MHz.
2. On the logic analyzer, set the clocks per division to 1.
3. Click on the set button in the clock box and ensure the
following:
- Clock edge "negative"
- Clock mode "internal"
- Set internal clock rate to "1 MHz"
- Clock qualifier "x"
- Logic analyzer "Pre-trigger samples 100"
"Post-trigger samples 1000"
"Threshold voltage (V) 3.5"
4. Make sure the Current address on the word generator is 0000.
5. Click the Cycle button on the word generator.
================================================================
Technical Reference Corrections
PAGE 14-22 - The picture of the opened logic analyzer is
incorrect. Since the manual was printed, the Time Base feature
has been removed and replaced with a Clocks per division
feature.
The "Time base" setting was used to set the logic analyzer's
display in units of seconds/division. The "Clocks per division"
setting is used to set the traces in units of clocks/division.
The number of clocks refers to the number of samples of the
data from the input terminals which have been taken.
Page 14-23 - The third paragraph discusses how to specify the
number of samples stored before and after triggering. The user
can also specify the number of samples by selecting the set
button in the clock box of the logic analyzer and making the
appropriate changes.
================================================================
Electronics Workbench is a registered trademark of Interactive
Image Technologies Ltd.
Copyright (c) Interactive Image Technologies Ltd., 1996.
没有合适的资源?快使用搜索试试~ 我知道了~
EWB 电子仿真小软件
共253个文件
lib:83个
ewb:49个
m15:22个
5星 · 超过95%的资源 需积分: 10 39 下载量 46 浏览量
2009-04-09
10:02:30
上传
评论 2
收藏 6.58MB RAR 举报
温馨提示
EWB 电子仿真小软件,短而强悍的小软件,提供基本的模拟和数字电路图绘制和电子仿真
资源推荐
资源详情
资源评论
收起资源包目录
EWB 电子仿真小软件 (253个子文件)
INFO.BAT 937B
GLOBAL.CNF 569B
GLOBAL.CNF 486B
EWBEXT.CNF 251B
EWB.CSP 288B
XSPICE32.DLL 1.22MB
GRAPHER.DLL 528KB
SPICEEWB.DLL 137KB
COMPDAT.DLL 131KB
ANALOG.DLL 126KB
EWBSPICE.DLL 102KB
CHIP.DLL 82KB
EWBTOPCB.DLL 81KB
DIGITAL.DLL 68KB
GETRES32.DLL 23KB
GETRES16.DLL 8KB
生命如四季.doc 21KB
两级共射放大器.ewb 98KB
桥式整流电路.ewb 96KB
ua727.ewb 85KB
ua741.ewb 76KB
音频功率放大电路(90w).ewb 71KB
共源共栅视频放大电路.ewb 62KB
通用滤波电路.ewb 39KB
三级放大电路.ewb 39KB
带通滤波器.ewb 37KB
五阶低通滤波电路.ewb 33KB
差动放大电路.ewb 32KB
峰值检波器.ewb 30KB
并联电压调整电路.ewb 30KB
共发射极放大电路.ewb 26KB
自举源极跟随器.ewb 25KB
经典1.ewb 24KB
高增益音频放大电路.ewb 24KB
移相电路.ewb 22KB
一阶高通滤波电路.ewb 21KB
乙类功率放大电路.ewb 21KB
rca3040(宽带运放).ewb 21KB
ua709.ewb 20KB
fet转移特性测试电路.ewb 18KB
zhenpower.ewb 18KB
STEROAMP.EWB 18KB
VIDEO.EWB 17KB
单管放大.ewb 16KB
REGULATE.EWB 15KB
两管放大电路.ewb 15KB
四管集成音频大功率放大器.ewb 15KB
poweramp.ewb 14KB
samp.ewb 13KB
两管直放式收音机.ewb 13KB
STEPDRV.EWB 12KB
am原理.ewb 12KB
am.ewb 11KB
2t.ewb 11KB
恒流源.ewb 9KB
Sample.ewb 9KB
2M-OSCIL.EWB 9KB
555VAR.EWB 9KB
untitled.ewb 9KB
DCOUNTER.EWB 9KB
1HP-FILT.EWB 9KB
RINGING.EWB 7KB
RS-FF.EWB 7KB
7SEGDEMO.EWB 7KB
RCCHARGE.EWB 7KB
DEFAULT.ewb 5KB
CHIP.EWX 1.08MB
DIGITAL.EWX 333KB
DIGITALD.EWX 326KB
ANALOG.EWX 301KB
ANALOGD.EWX 252KB
EWBTOPCB.EWX 148KB
EWBSPICE.EWX 58KB
SPICEEWB.EWX 8KB
EWB50C.EXE 3.32MB
WEWB32.EXE 1.82MB
SYS_INFO.EXE 28KB
WHAT.EXE 3KB
EWBFNT.FON 16KB
WEWB.HLP 1.69MB
DEFAULT.HPL 217B
EWB.INI 134B
DEISL1.ISU 10KB
BURR_BRN.LIB 206KB
INTRNTNL.LIB 201KB
MAXIM.LIB 85KB
MOTOROL2.LIB 75KB
PHILIPS1.LIB 62KB
GENERAL1.LIB 57KB
NATIONL2.LIB 50KB
NATIONL2.LIB 50KB
ELANTEC.LIB 50KB
ANALOG.LIB 50KB
MOTOROLA.LIB 47KB
NATIONL2.LIB 44KB
PHILIPS2.LIB 39KB
ZETEX.LIB 37KB
IRF_IGBT.LIB 33KB
NATIONL3.LIB 31KB
ZETEX.LIB 30KB
共 253 条
- 1
- 2
- 3
资源评论
- 啊洪的一个2014-03-09资源不错 非常实用 好用
- shuyu082012-10-30简单实用,很适合初学者使用!
铁樵
- 粉丝: 75
- 资源: 109
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功