没有合适的资源?快使用搜索试试~ 我知道了~
资源推荐
资源详情
资源评论
Advanced Optowave Corporation
Operation Manual
Model Awave-355 nm Series Laser
105 Comac St, Ronkonkoma, NY 11779, USA
Tel: (631) 750-6035 \ Fax (631) 803-4445
REV 2.1
1
Table of Contents
Symbols used within the manual..........................................p 3
1. Laser Safety and...................................................................p 4
2. AOC Laser Safety Features..................................................p 7
3. AOC Laser Systems..............................................................p 9
4. Laser System Unpacking......................................................p 10
5. Laser System Environmental Requirements........................p 12
6. System Installation...............................................................p 13
7. Laser Start Up Procedure.....................................................p 17
8. Laser Shut Down Procedure.................................................p 23
9. Front Panel Control and Signal Inputs..................................p 24
10. Laser PC RS232 Control (Hyper-terminal)...........................p 27
11. Daily Operation.....................................................................p 34
12. First Pulse Suppression........................................................p 37
13. Laser Power and Pulse Energy Control................................p 38
14. Warranty...............................................................................p 39
2
REV 2.1
Symbols used in this manual
The following symbols are used throughout this manual to alert
you to information that requires special attention.
Laser Radiation:
Laser radiation is symbolized by this symbol.
Caution:
This symbol
alerts you to an operation or procedure that
could result in equipment damage if not preformed properly.
Tip:
This symbol alerts you to advice that will assist you.
Electrical Hazard:
This symbol alerts you to the presents of an
electrical hazard.
Laser Eye Protection:
This symbol alerts you in that laser eye
protection is necessary.
Note:
This symbol is to alert you to important advisory information.
3
1 Laser Safety and AOC Laser Safety Features
1.1 LASER SAFETY
DANGER!
Awave-355nm laser is a Class IV-High Power Laser.
Extreme care should be taken when operating. The laser beam is a fire
and safety hazard. Only personnel who are familiar with the safety
precautions listed in this manual should operate the laser system.
Precautions must be taken to prevent accidental exposure to direct or
reflected laser beam. Both diffuse and specula reflections can cause
severe skin or eye damages. Proper eye protection must be worn at
all times. Direct eye contact with the output beam from the laser will cause
serious damage and possible blindness.
Safety Operation of Class IV-high Power laser.
The greatest danger is the direct exposure to the main laser beam when using a laser.
In addition to the main beam, a few smaller weaker power beams may exit at different angles
near the laser system. The weaker beams may still be sufficiently intense to cause eye damage.
Laser light are powerful enough to burn skin, clothing or paint. They can ignite volatile
substances such as solvents even at some distance. The laser beam can damage light sensors
in video cameras and photo diodes. The user is advised to follow the precautions below and in
this manual.
Don’t look at the output beam directly. Specula and diffuse reflections are hazardous.
• Avoid wearing jewelry or any reflective items when operating the laser.
• Use protective eye wear that is right for 355nm I.e optically dense at the 355nm
wavelengths of operations at all times. Consult your organization's Laser Safety
Officer in accordance with your laser safety procedures.
• Use an UV fluorescence card to verify that the laser beam is off for safety.
• Be sure to use non-reflective beam stops to block the laser beam.
• Set up the laser beam so that it is not at eye level, the beam should be above or
below eye level both at a seated position and a standing position.
4
• Post highly visible warning-signs near the laser operation area for Class IV laser
products.
• Set up a dangerous zone around the laser, use safety interlocks to prevent non-
experienced personnel from entering into working area.
• Laser light is very bright and intense compared with conventional light source. It
poses a significant safety hazard. All laser users, and every one near the laser
system, should be aware of the dangers of using a class IV laser such as the
Awave-355nm laser system.
• Observe and follow all safety precautions in this manual.
• Extreme cautions should be taken when using volatile substances in the laser area.
• Only the qualified users who are familiar with standard laser safety practices and
who are aware of the dangers involved, should be allowed to access the laser.
• Never direct exposure to the laser beam. The intensity of the beam can easily
cause flesh burns or ignite clothing.
DANGER! VISIBLE, INVISIBLE AND ULTRA VIOLET RADIATION
The Awave-355nm Laser produces both visible and invisible
radiation. The invisible radiation has a wavelength of 1064nm which
corresponds to the infrared (IR) optical region and 355-351nm which
corresponds to the Ultra Violet (UV) optical region. The visible
radiation is 532-527nm which corresponds to the Green (GR) optical
region. These radiations can easily cause permanent damage to the
retina.
5
剩余41页未读,继续阅读
资源评论
GJZGRB
- 粉丝: 1550
- 资源: 6281
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功