1. 计算机命令:
PCA login: root ;使用root用户
password: linux ;口令是linux
# shutdown -h now ;同init 0 关机
# logout
# login
# ifconfig ;显示IP地址
# ifconfig eth0 <ip address> netmask <netmask> ;设置IP地址
# ifconfig eht0 <ip address> netmask <netmask> down ; 删除IP地址
# route add 0.0.0.0 gw <ip>
# route del 0.0.0.0 gw <ip>
# route add default gw <ip> ;设置网关
# route del default gw <ip> ;删除网关
# route ;显示网关
# ping <ip>
# telnet <ip>
2. 交换机支持的命令:
交换机基本状态:
switch: ;交换机的ROM状态
rommon> ;路由器的ROM状态
hostname> ;用户模式
hostname# ;特权模式
hostname(config)# ;全局配置模式
hostname(config-if)# ;接口状态
交换机口令设置:
switch>enable ;进入特权模式
switch#config terminal ;进入全局配置模式
switch(config)#hostname <hostname> ;设置交换机的主机名
switch(config)#enable secret xxx ;设置特权加密口令
switch(config)#enable password xxa ;设置特权非密口令
switch(config)#line console 0 ;进入控制台口
switch(config-line)#line vty 0 4 ;进入虚拟终端
switch(config-line)#login ;允许登录
switch(config-line)#password xx ;设置登录口令xx
switch#exit ;返回命令
交换机VLAN设置:
switch#vlan database ;进入VLAN设置
switch(vlan)#vlan 2 ;建VLAN 2
switch(vlan)#no vlan 2 ;删vlan 2
switch(config)#int f0/1 ;进入端口1
switch(config-if)#switchport access vlan 2 ;当前端口加入vlan 2
switch(config-if)#switchport mode trunk ;设置为干线
switch(config-if)#switchport trunk allowed vlan 1,2 ;设置允许的vlan
switch(config-if)#switchport trunk encap dot1q ;设置vlan 中继
switch(config)#vtp domain <name> ;设置发vtp域名
switch(config)#vtp password <word> ;设置发vtp密码
switch(config)#vtp mode server ;设置发vtp模式
switch(config)#vtp mode client ;设置发vtp模式
交换机设置IP地址:
switch(config)#interface vlan 1 ;进入vlan 1
switch(config-if)#ip address <IP> <mask> ;设置IP地址
switch(config)#ip default-gateway <IP> ;设置默认网关
switch#dir flash: ;查看闪存
交换机显示命令:
switch#write ;保存配置信息
switch#show vtp ;查看vtp配置信息
switch#show run ;查看当前配置信息
switch#show vlan ;查看vlan配置信息
switch#show interface ;查看端口信息
switch#show int f0/0 ;查看指定端口信息
3. 路由器支持的命令:
路由器显示命令:
router#show run ;显示配置信息
router#show interface ;显示接口信息
router#show ip route ;显示路由信息
router#show cdp nei ;显示邻居信息
router#reload ;重新起动
路由器口令设置:
router>enable ;进入特权模式
router#config terminal ;进入全局配置模式
router(config)#hostname <hostname> ;设置交换机的主机名
router(config)#enable secret xxx ;设置特权加密口令
router(config)#enable password xxb ;设置特权非密口令
router(config)#line console 0 ;进入控制台口
router(config-line)#line vty 0 4 ;进入虚拟终端
router(config-line)#login ;要求口令验证
router(config-line)#password xx ;设置登录口令xx
router(config)#(Ctrl+z) ; 返回特权模式
router#exit ;返回命令
路由器配置:
router(config)#int s0/0 ;进入Serail接口
router(config-if)#no shutdown ;激活当前接口
router(config-if)#clock rate 64000 ;设置同步时钟
router(config-if)#ip address <ip> <netmask> ;设置IP地址
router(config-if)#ip address <ip> <netmask> second ;设置第二个IP
router(config-if)#int f0/0.1 ;进入子接口
router(config-subif.1)#ip address <ip> <netmask> ;设置子接口IP
router(config-subif.1)#encapsulation dot1q <n> ;绑定vlan中继协议
router(config)#config-register 0x2142 ;跳过配置文件
router(config)#config-register 0x2102 ;正常使用配置文件
router#reload ;重新引导
路由器文件操作:
router#copy running-config startup-config ;保存配置
router#copy running-config tftp ;保存配置到tftp
router#copy startup-config tftp ;开机配置存到tftp
router#copy tftp flash: ;下传文件到flash
router#copy tftp startup-config ;下载配置文件
ROM状态:
Ctrl+Break ;进入ROM监控状态
rommon>confreg 0x2142 ;跳过配置文件
rommon>confreg 0x2102 ;恢复配置文件
rommon>reset ;重新引导
rommon>copy xmodem:<sname> flash:<dname> ;从console传输文件
rommon>IP_ADDRESS=10.65.1.2 ;设置路由器IP
rommon>IP_SUBNET_MASK=255.255.0.0 ;设置路由器掩码
rommon>TFTP_SERVER=10.65.1.1 ;指定TFTP服务器IP
rommon>TFTP_FILE=c2600.bin ;指定下载的文件
rommon>tftpdnld ;从tftp下载
rommon>dir flash: ;查看闪存内容
rommon>boot ;引导IOS
静态路由:
ip route <ip-address> <subnet-mask> <gateway> ;命令格式
router(config)#ip route 2.0.0.0 255.0.0.0 1.1.1.2 ;静态路由举例
router(config)#ip route 0.0.0.0 0.0.0.0 1.1.1.2 ;默认路由举例
动态路由:
router(config)#ip routing ;启动路由转发
router(config)#router rip ;启动RIP路由协议。
router(config-router)#network <netid> ;设置发布路由
router(config-router)#negihbor <ip> ;点对点帧中继用。
帧中继命令:
router(config)#frame-relay switching ;使能帧中继交换
router(config-s0)#encapsulation frame-relay ;使能帧中继
router(config-s0)#fram-relay lmi-type cisco ;设置管理类型
router(config-s0)#frame-relay intf-type DCE ;设置为DCE
router(config-s0)#frame-relay dlci 16 ;
router(config-s0)#frame-relay local-dlci 20 ;设置虚电路号
router(config-s0)#frame-relay interface-dlci 16 ;
router(config)#log-adjacency-changes ;记录邻接变化
router(config)#int s0/0.1 point-to-point ;设置子接口点对点
router#show frame pvc ;显示永久虚电路
router#show frame map ;显示映射
基本访问控制列表:
router(config)#access-list <number> permit|deny <source_ip> <wild|any>
router(config)#interface <interface> ;default:deny any
router
华为思科交换机,路由器配置命令
5星 · 超过95%的资源 需积分: 13 13 浏览量
2008-07-22
11:18:03
上传
评论
收藏 13KB RAR 举报
Tomsen_Tian
- 粉丝: 27
- 资源: 28
最新资源
- 80632180.jpg
- 李旭国体注入追踪[5.0](1).zip
- semantic.c
- C语言基础-C语言编程基础之Leetcode编程题解之第39题组合总和.zip
- C语言基础-C语言编程基础之Leetcode编程题解之第38题外观数列.zip
- C语言基础-C语言编程基础之Leetcode编程题解之第37题解数独.zip
- C语言基础-C语言编程基础之Leetcode编程题解之第36题有效的数独.zip
- C语言基础-C语言编程基础之Leetcode编程题解之第35题搜索插入位置.zip
- index.wxml
- C语言基础-C语言编程基础之Leetcode编程题解之第33题搜索旋转排序数组.zip
资源上传下载、课程学习等过程中有任何疑问或建议,欢迎提出宝贵意见哦~我们会及时处理!
点击此处反馈