没有合适的资源?快使用搜索试试~ 我知道了~
AK09911-preliminary-E-00.pdf
需积分: 10 12 下载量 95 浏览量
2017-04-16
11:46:01
上传
评论
收藏 883KB PDF 举报
温馨提示
试读
34页
AK09911芯片datasheet
资源推荐
资源详情
资源评论
Confidential
[AK09911]
MSXXXX-E-pre00 2012/12
- 1 -
AK09911
3-axis Electronic Compass
1. Features
A 3-axis electronic compass IC with high sensitive Hall sensor technology.
Best adapted to pedestrian city navigation use for cell phone and other portable appliance.
Functions:
3-axis magnetometer device suitable for compass application
Built-in A to D Converter for magnetometer data out
14-bit data out for each 3-axis magnetic component
Sensitivity: 0.6 µT/LSB (typ.)
Serial interface
I
2
C bus interface
Standard, Fast and High-speed mode (up to 2.5 MHz) compliant with Philips I2C specification Ver.2.1
Operation mode
Power-down, Single measurement, Continuous measurement, Self-test and Fuse ROM access
DRDY function for measurement data ready
Magnetic sensor overflow monitor function
Built-in oscillator for internal clock source
Power on Reset circuit
Self test function with internal magnetic source
Operating temperatures:
-30˚C to +85˚C
Operating supply voltage:
Analog power supply +2.4V to +3.6V
Digital Interface supply +1.65V to analog power supply voltage
Current consumption:
Power-down: 3 µA (typ.)
Measurement:
Average current consumption at 100 Hz repetition rate: 2.4 mA (typ.)
Package:
AK09911C 8-pin WL-CSP (BGA): 1.2 mm × 1.2 mm × 0.5 mm (typ.)
Confidential
[AK09911]
MSXXXX-E-pre00 2012/12
- 2 -
2. Overview
AK09911 is 3-axis electronic compass IC with high sensitive Hall sensor technology.
Small package of AK09911 incorporates magnetic sensors for detecting terrestrial magnetism in the X-axis, Y-axis, and
Z-axis, a sensor driving circuit, signal amplifier chain, and an arithmetic circuit for processing the signal from each sensor.
Self test function is also incorporated. From its compact foot print and thin package feature, it is suitable for map heading
up purpose in GPS-equipped cell phone to realize pedestrian navigation function.
AK09911 has the following features:
(1) Silicon monolithic Hall-effect magnetic sensor with magnetic concentrator realizes 3-axis magnetometer on a
silicon chip. Analog circuit, digital logic, power block and interface block are also integrated on a chip.
(2) Wide dynamic measurement range and high resolution with lower current consumption.
Output data resolution: 14-bit (0.6 µT/LSB)
Measurement range: ±4900 µT
Average current at 100 Hz repetition rate: 2.4 mA (typ.)
(3) Digital serial interface
I
2
C bus interface to control AK09911 functions and to read out the measured data by external CPU. A
dedicated power supply for I
2
C bus interface can work in low-voltage apply as low as 1.65V.
(4) DRDY register informs to system that measurement is end and set of data in registers are ready to be read.
(5) Device is worked by on-chip oscillator so no external clock source is necessary.
(6) Self test function with internal magnetic source to confirm magnetic sensor operation on end products.
Confidential
[AK09911]
MSXXXX-E-pre00 2012/12
- 3 -
3. Table of Contents
1. Features .............................................................................................................................. 1
2. Overview .............................................................................................................................. 2
3. Table of Contents ................................................................................................................. 3
4. Circuit Configration .............................................................................................................. 5
4.1. Block Diagram .............................................................................................................. 5
4.2. Block Function .............................................................................................................. 5
4.3. Pin Function .................................................................................................................. 6
5. Overall Characteristics ........................................................................................................ 7
5.1. Absolute Maximum Ratings .......................................................................................... 7
5.2. Recommended Operating Conditions .......................................................................... 7
5.3. Electrical Characteristics .............................................................................................. 7
5.3.1. DC Characteristics ................................................................................................. 7
5.3.2. AC Characteristics ................................................................................................. 8
5.3.3. Analog Circuit Characteristics ................................................................................ 9
5.3.4. I
2
C Bus Interface .................................................................................................. 10
6. Function Explanation ......................................................................................................... 13
6.1. Power States ............................................................................................................... 13
6.2. Reset Functions .......................................................................................................... 13
6.3. Operation Mode .......................................................................................................... 14
6.4. Description of Each Operation Mode ......................................................................... 15
6.4.1. Power-down Mode ............................................................................................... 15
6.4.2. Single Measurement Mode .................................................................................. 15
6.4.3. Continuous Measurement Mode 1, 2, 3 and 4 .................................................... 16
6.4.4. Self-test Mode ...................................................................................................... 19
6.4.5. Fuse ROM Access Mode ..................................................................................... 19
7. Serial Interface .................................................................................................................. 20
7.1. Data Transfer .............................................................................................................. 20
7.1.1. Change of Data .................................................................................................... 20
7.1.2. Start/Stop Condition ............................................................................................. 20
7.1.3. Acknowledge ........................................................................................................ 21
7.1.4. Slave Address ...................................................................................................... 21
7.2. WRITE Instruction ....................................................................................................... 22
7.3. READ Instruction ........................................................................................................ 23
7.3.1. One Byte READ ................................................................................................... 23
7.3.2. Multiple Byte READ ............................................................................................. 23
7.4. High-speed Mode (Hs-mode) ..................................................................................... 24
8. Registers ........................................................................................................................... 25
8.1. Description of Registers ............................................................................................. 25
8.2. Register Map .............................................................................................................. 26
8.3. Detailed of Description of Register ............................................................................. 27
8.3.1. WIA: Who I Am ..................................................................................................... 27
8.3.2. INFO: Information ................................................................................................ 27
8.3.3. ST1: Status 1 ........................................................................................................ 27
8.3.4. HXL to HZH: Measurement data .......................................................................... 28
8.3.5. TMPS: Dummy Register ...................................................................................... 28
8.3.6. ST2: Status 2 ........................................................................................................ 29
8.3.7. CNTL1: Dummy Register ..................................................................................... 29
8.3.8. CNTL2: Control 2 ................................................................................................. 29
8.3.9. CNTL3: Control 3 ................................................................................................. 30
8.3.10. TS1: Test ............................................................................................................ 30
8.3.11. ASAX, ASAY, ASAZ: Sensitivity Adjustment Values ........................................... 30
9. Example of Recommended External Connection ............................................................. 31
10. Package ........................................................................................................................... 32
10.1. Marking ..................................................................................................................... 32
10.2. Pin Assignment ......................................................................................................... 32
10.3. Outline Dimensions .................................................................................................. 33
Confidential
[AK09911]
MSXXXX-E-pre00 2012/12
- 5 -
4. Circuit Configration
4.1. Block Diagram
3-axis
Hall
sensor
MUX
SDA
Chopper
SW
HE-Drive
Pre
-
AMP
Integrator&ADC
Interface Logic
& Register
SCL
VDD
VREF
Timing
Control
VID
OSC
Magnetic source
VSS
POR
FUSE ROM
TST
RSTN
CAD
4.2. Block Function
Block
Function
3-axis Hall sensor
Monolithic Hall elements.
MUX
Multiplexer for selecting Hall elements.
Chopper SW
Performs chopping.
HE-Drive
Magnetic sensor drive circuit for constant-current driving of sensor.
Pre-AMP
Fixed-gain differential amplifier used to amplify the magnetic sensor signal.
Intergrator & ADC
Integrates and amplifies pre-AMP output and performs analog-to-digital
conversion.
OSC
Generates an operating clock for sensor measurement.
POR
Power On Reset circuit. Generates reset signal on rising edge of VDD.
VREF
Generates reference voltage and current.
Interface Logic
&
Register
Exchanges data with an external CPU.
I2C bus interface using two pins, namely, SCL and SDA. Standard, Fast and
High-speed modes are supported. The low-voltage specification can be supported
by applying 1.65V to the VID pin.
Timing Control
Generates a timing signal required for internal operation from a clock generated by
the OSC.
Magnetic Source
Generates magnetic field for self test of magnetic sensor.
FUSE ROM
Fuse for adjustment.
剩余33页未读,继续阅读
资源评论
free_sz
- 粉丝: 31
- 资源: 6
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功