RT2870的LINUX下的修改版驱动

iwpriv ================= This is detailed explanation of each parameters for iwpriv. Before reading this document, make sure you already read README. ------------------------------------------------------------------------------------------------------- USAGE: iwpriv ra0 set [parameters]=[val] NOTE: Execute one iwpriv/set command simultaneously. where [parameters] [val] {range} ----------------- ------------------------------------------------- CountryRegion {0~7} ::Set country region 0: 1 ~ 11 ch 1: 1 ~ 13 ch 2: 10, 11 ch 3: 10 ~ 13 ch 4: 14 ch 5: 1 ~ 14 ch 6: 3 ~ 9 ch 7: 5 ~ 13 Channel CountryRegionForABand {0~10} ::Set country region for A band 0: 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 ch 1: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 ch 2: 36, 40, 44, 48, 52, 56, 60, 64 ch 3: 52, 56, 60, 64, 149, 153, 157, 161 ch 4: 149, 153, 157, 161, 165 ch 5: 149, 153, 157, 161 ch 6: 36, 40, 44, 48 ch 7: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 ch 8: 52, 56, 60, 64 ch 9: 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 ch SSID {0~z, 1~32 ascii characters} ::Set AP SSID WirelessMode {0~10} ::Set Wireless Mode 0: legacy 11b/g mixed 1: legacy 11B only 2: legacy 11A only 3: legacy 11a/b/g mixed 4: legacy 11G only 5: 11ABGN mixed 6: 11N only 7: 11GN mixed 8: 11AN mixed 9: 11BGN mixed 10: 11AGN mixed Channel depends on CountryRegion or CountryRegionForABand ::Set Channel BGProtection {0~2} ::Set 11B/11G Protection 0:Auto, 1:Always on, 2:Always off TxPreamble {0~2} ::Set TxPreamble 0:Preamble Long, 1:Preamble Short, 2:Auto RTSThreshold {1~2347} ::Set RTS Threshold FragThreshold {256~2346} ::Set Fragment Threshold TxBurst {0,1} ::Set TxBurst Enable or Disable 0:Disable, 1:Enable NetworkType {Infra,Adhoc} ::Set Network type AuthMode {OPEN,SHARED,WEPAUTO,WPAPSK,WPA2PSK,WPANONE} ::Set Authentication Mode EncrypType {NONE,WEP,TKIP,AES} ::Set Encryption Type DefaultKeyID {1~4} ::Set Default Key ID Key1 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key1 String Key2 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key2 String Key3 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key3 String Key4 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key4 String WPAPSK {8~63 ascii or 64 hex characters} ::WPA Pre-Shared Key WmmCapable {0,1} ::Set WMM Capable 0:Disable WMM, 1:Enable WMM PSMode {CAM, MAX_PSP, FAST_PSP} ::Set Power Saving Mode HtBw {0,1} ::Set BandWidth 0: 20Hz 1: 40Hz HtMcs {0 ~ 15, 33} ::Set MCS 33: Auto Rate HtGi {0,1} ::Set Guard Interval(GI) 0: long GI 1: short GI HtOpMode {0,1} ::Set HT Operation Mode 0: HT mixed format 1: HT greenfield format HtExtcha {0,1} ::Set Extended Channel Switch Announcement 0: Below 1: Above HtMpduDensity {0 ~ 7} ::Set The Minimum Time Between MPDUs within an AMPDU HtBaWinSize {1 ~ 64} ::Set BA WinSize HtRdg {0,1} ::Set RDG Capable 0: Disabled 1: Enabled HtAmsdu {0,1} ::Set AMSDU Capable 0: Disabled 1: Enabled HtAutoBa {0,1} ::Set Auto BA Capable 0: Disabled 1: Enabled HtProtect {0,1} ::Set HT Protect Capable 0: Disabled 1: Enabled FixedTxMode {CCK, OFDM} :: Set Fixed Tx Mode for fixed rate setting Mode = CCK MCS = 0 => 1Mbps = 1 => 2Mbps = 2 => 5.5 Mbps = 3 => 11 Mbps Mode = OFDM MCS = 0 => 6Mbps = 1 => 9Mbps = 2 => 12Mbps = 3 => 18Mbps = 4 => 24Mbps = 5 => 36Mbps = 6 => 48Mbps = 7 => 54Mbps Examples =================================================================== ------------------------------------------------------------------------------------------------------- a> Config STA to link with AP which is OPEN/NONE(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=OPEN 3. iwpriv ra0 set EncrypType=NONE 4. iwpriv ra0 set SSID="AP's SSID" b> Config STA to link with AP which is SHARED/WEP(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=SHARED 3. iwpriv ra0 set EncrypType=WEP 4. iwpriv ra0 set DefaultKeyID=1 5. iwpriv ra0 set Key1="AP's wep key" 6. iwpriv ra0 set SSID="AP's SSID" c> Config STA to link with AP which is WPAPSK/TKIP(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=WPAPSK 3. iwpriv ra0 set EncrypType=TKIP 4. iwpriv ra0 set SSID="AP's SSID" 5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key" 6. iwpriv ra0 set SSID="AP's SSID" d> Config STA to link with AP which is WPAPSK/AES(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=WPAPSK 3. iwpriv ra0 set EncrypType=AES 4. iwpriv ra0 set SSID="AP's SSID" 5. iwpriv ra0 set WPAPSK="AP's wpa-preshared key" 6. iwpriv ra0 set SSID="AP's SSID" e> Config STA to link with AP which is WPA2PSK/TKIP(Authentication/Encryption) 1. iwpriv ra0 set NetworkType=Infra 2. iwpriv ra0 set AuthMode=WPA2PSK 3. iwpriv ra0 set EncrypType=TKIP 4. iwpriv ra0 set SSID="AP's SSID" 5. iwpriv ra0 set WPAPSK=12345678 6. iwpriv ra0 set SSID="AP's SSID" f> Config STA to create/link as adhoc mode, which is OPEN/NON