micro_FAT_FileSystem

FatFs/Tiny-FatFs Module Source Files R0.04 (C)ChaN, 2007 FILES ff.h Common include file for FatFs and application module. ff.c FatFs module. tff.h Common include file for Tiny-FatFs and application module. tff.c Tiny-FatFs module. diskio.h Common include file for (Tiny-)FatFs and disk I/O module. integer.h Alternative type definitions for integer variables. Low level disk I/O module is not included in this archive because the FatFs/Tiny-FatFs module is only a generic file system layer and not depend on any specific storage device. You have to provide a low level disk I/O module that written to control your storage device. CONFIGURATION OPTIONS There are several configuration options for various envilonment and requirement. The configuration options are defined in header files, ff.h and tff.h. _MCU_ENDIAN This is the most impotant option that depends on the processor architecture. When target device corresponds to either or both of following terms, the _MCU_ENDIAN must be set to 2 to force FatFs to access FAT structure in byte-by-byte. If not the case, this can be set to 1 for good code efficiency. The initial value is 0 (must be set to 1 or 2 properly). - Muti-byte integers (short, long) are stored in Big-Endian. - Address miss-aligned memory access results in an incorrect behavior. _FS_READONLY When application program does not require any write function, _FS_READONLY can be set to 1 to eliminate writing code to reduce module size. This setting should be reflected to configurations of low level disk I/O module if available. The initial value is 0 (R/W). _FS_MINIMIZE When application program requires only file read/write function, _FS_MINIMIZE can be defined to eliminate some functions to reduce the module size. The initial value is 0 (full function). _DRIVES Number of drives to be used. This option is not supported on Tiny-FatFs. The initial value is 2. _FAT32 When _FAT32 is set to 1, the FAT32 support is added with an additional code size. This is for only Tiny-FatFs and not supported on FatFs. FatFs always supports all FAT type. The initial value is 0 (disabled). _USE_SJIS When _USE_SJIS is defined, Shift-JIS code set can be used as a file name, otherwire second byte of double-byte characters will be collapted. This is initially defined. _USE_MKFS When _USE_MKFS is defined and _FS_READONLY is set to 0, f_mkfs function is enabled. This is for only FatFs module and not supported on Tiny-FatFs. This is initialy undefined (not available). Following table shows which function is removed by configuratin options. _FS_MINIMIZE _FS_MINIMIZE _FS_READONLY _USE_MKFS (1) (2) (1) (undef) f_mount f_open f_close f_read f_lseek f_write x f_sync x f_opendir x f_readdir x f_stat x x f_getfree x x x f_unlink x x x f_mkdir x x x f_chmod x x x f_rename x x x f_mkfs x x AGREEMENTS The FatFs/Tiny-FatFs module is a free software and there is no warranty. The FatFs/Tiny-FatFs module is opened for education, reserch and development. You can use and/or modify it for personal, non-profit or profit use without any restriction under your responsibility. REVISION HISTORY Feb 26, 2006 R0.00 Prototype Apr 29, 2006 R0.01 First stable version Jun 01, 2006 R0.02 Added FAT12. Removed unbuffered mode. Fixed a problem on small (<32M) patition. Jun 10, 2006 R0.02a Added a configuration option _FS_MINIMUM. Sep 22, 2006 R0.03 Added f_rename(). Changed option _FS_MINIMUM to _FS_MINIMIZE. Dec 11, 2006 R0.03a Improved cluster scan algolithm to write files fast. Fixed f_mkdir() creates incorrect directory on FAT32. Feb 04, 2007 R0.04 Supported multiple drive system. Changed some APIs for multiple drive system. Added f_mkfs().