没有合适的资源?快使用搜索试试~ 我知道了~
ISO 16750-1-2006.pdf
需积分: 10 14 下载量 52 浏览量
2019-08-17
10:33:37
上传
评论 1
收藏 639KB PDF 举报
温馨提示
试读
20页
Road vehicles — Environmental conditions and testing for electrical and electronic equipment — Part 1:General
资源推荐
资源详情
资源评论
Reference number
ISO 16750-1:2006(E)
©
ISO 2006
INTERNATIONAL
STANDARD
ISO
16750-1
Second edition
2006-08-01
Road vehicles — Environmental
conditions and testing for electrical
and electronic equipment —
Part 1:
General
Véhicules routiers — Spécifications d'environnement et essais de
l'équipement électrique et électronique —
Partie 1: Généralités
ISO 16750-1:2006(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
© ISO 2006
All rights reserved. Unless otherwise specified, no part of this publication may be reproduced or utilized in any form or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail copyright@iso.org
Web www.iso.org
Published in Switzerland
ii
© ISO 2006 – All rights reserved
ISO 16750-1:2006(E)
© ISO 2006 – All rights reserved iii
Contents Page
Foreword............................................................................................................................................................ iv
Introduction ........................................................................................................................................................ v
1 Scope ..................................................................................................................................................... 1
2 Normative references ........................................................................................................................... 1
3 Terms and definitions........................................................................................................................... 1
4 Classification by mounting location ................................................................................................... 3
4.1 Engine compartment ............................................................................................................................ 3
4.2 Passenger compartment...................................................................................................................... 3
4.3 Luggage compartment/load compartment......................................................................................... 3
4.4 Mounting on the exterior/in cavities ................................................................................................... 3
4.5 Other mounting locations .................................................................................................................... 4
5 Operating modes .................................................................................................................................. 4
5.1 Operating mode 1 ................................................................................................................................. 4
5.2 Operating mode 2 ................................................................................................................................. 4
5.3 Operating mode 3 ................................................................................................................................. 4
6 Functional status classification .......................................................................................................... 4
6.1 General................................................................................................................................................... 4
6.2 Class A................................................................................................................................................... 5
6.3 Class B ................................................................................................................................................... 5
6.4 Class C ................................................................................................................................................... 5
6.5 Class D ................................................................................................................................................... 5
6.6 Class E ................................................................................................................................................... 5
7 Tests and requirements ....................................................................................................................... 5
7.1 General................................................................................................................................................... 5
7.2 General test conditions ........................................................................................................................ 5
7.3 Test sequence ....................................................................................................................................... 6
8 Designation ........................................................................................................................................... 6
8.1 Coding.................................................................................................................................................... 6
8.2 Use of Code Z “as agreed” .................................................................................................................. 7
Annex A (informative) Example for a test sequence plan .............................................................................. 8
Annex B (informative) Example of life test/statement of reliability............................................................... 9
ISO 16750-1:2006(E)
iv © ISO 2006 – All rights reserved
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 2.
The main task of technical committees is to prepare International Standards. Draft International Standards
adopted by the technical committees are circulated to the member bodies for voting. Publication as an
International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this document may be the subject of patent
rights. ISO shall not be held responsible for identifying any or all such patent rights.
ISO 16750-1 was prepared by Technical Committee ISO/TC 22, Road vehicles, Subcommittee SC 3,
Electrical and electronic equipment.
This second edition cancels and replaces the first edition (ISO 16750-1:2003), which has been technically
revised.
ISO 16750 consists of the following parts, under the general title Road vehicles — Environmental conditions
and testing for electrical and electronic equipment:
⎯ Part 1: General
⎯ Part 2: Electrical loads
⎯ Part 3: Mechanical loads
⎯ Part 4: Climatic loads
⎯ Part 5: Chemical loads
剩余19页未读,继续阅读
资源评论
xuguanghe_xgh
- 粉丝: 5
- 资源: 29
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功