RT3572_Linux_STA_v2.5.0.0.DPO.zip_V2

=================================================================================================== ATE Test Command Format for station driver ****** IMPORTANT ****** If you are not familiar with hardware, it is recommanded not to modify hardware default value. It may damage hardware. =================================================================================================== Usage: iwpriv ra0 [act] [parameters]=[val] where [act] [parameters] [val] constraints explaination ----- ------------- ----------------- -------------------------------- ===================================== 1. Set ATE actions. Value: ATESTART - Start ATE function and stop station function. ATESTOP - Stop ATE function and start station function. TXCONT - Start continuous TX, for power mask. TXCARR - Start carrier test, for frequency calibration. TXFRAME - Transmit frame, for EVM. RXFRAME - Continuous RX, for PER/FER. 1.1 ATEDA Set ATE frame header destination address. Value: xx:xx:xx:xx:xx:xx ; hex 1.2 ATESA Set ATE frame header source addr. Value: xx:xx:xx:xx:xx:xx ; hex 1.3 ATEBSSID Set ATE frame header BSSID. Value: xx:xx:xx:xx:xx:xx ; hex 1.4 ATECHANNEL Set ATE Channel, deimal. Value: 802.11b/g: 1 ~ 14 depends on CountryRegion setting 1.5 ATETXPOW0 Set ATE Tx power for Antenna 1. Value: 0 ~ 31 ; 2.4GHz, deimal -7 ~15 ; 5.5GHz, deimal 1.6 ATETXPOW1 Set ATE Tx power for Antenna 2. Value: 0 ~ 31 ; 2.4GHz, decimal -7 ~15 ; 5.5GHz, deimal 1.7 ATETXFREQOFFSET Set ATE RF frequency offset. Value: 0 ~ 63 ; unit: 2KHz, decimal 1.8 ATETXLEN Set ATE frame length. Value: 24 ~ 2312 ; decimal 1.9 ATETXCNT Set ATE frame Tx count. Value: 1 ~ ; 32-bit, decimal 1.10 ATETXMODE (Refer to TxMode) Set ATE Tx Mode. Value: 0: CCK 802.11b 1: OFDM 802.11g 2: HT_MIX 802.11b/g/n 3: Green Field 802.11n 1.11 ATETXBW (Refer to TxMode) Set ATE Tx and Rx Bandwidth. Value: 0: 20MHz 1: 40MHz 1.12 ATETXGI (Refer to TxMode) Set ATE Tx Guard Interval. Value: 0: Long 1: Short 1.13 ATETXMCS (Refer to TxMode) Set ATE Tx MCS type. Value: 0 ~ 15 1.14 ATETXANT Set ATE TX antenna. Value: 0: All 1: Antenna one 2: Antenna two 1.15 ATERXANT Set ATE RX antenna. Value: 0: All 1: Antenna one 2: Antenna two 3: Antenna three 1.16 ATERXFER Set ATE to periodically reset and show up RxCount (per-second) and RxTotalCount. Value: 0: Disable counter visability 1: Enable counter visability 1.17 ATESHOW Show all parameters of ATE. Value: 1 1.18 ATEHELP List all commands of ATE. Value: 1 1.19 ResetCounter Reset statistic counter. Value: 1 1.20 ATERRF Read all of the RF registers. Value: 1 1.21 ATEWRF1 Write the RF register 1. Value: xxxxxxxx ;32-bit, hex 1.22 ATEWRF2 Write the RF register 2. Value: xxxxxxxx ;32-bit, hex 1.23 ATEWRF3 Write the RF register 3. Value: xxxxxxxx ;32-bit, hex 1.24 ATEWRF4 Write the RF register 4. Value: xxxxxxxx ;32-bit, hex 1.25 ATELDE2P Overwrite all EEPROM contents Value: 1 E.g. iwpriv ra0 set ATELDE2P=1 1.26 ATERE2P Display all EEPROM content. Value: 1 E.g. iwpriv ra0 set ATERE2P=1 =================================================================================================== 2. Examples: ========= 2.1 Check EVM & Power iwpriv ra0 set ATE=ATESTART iwpriv ra0 set ATEDA=00:11:22:33:44:55 iwpriv ra0 set ATESA=00:aa:bb:cc:dd:ee iwpriv ra0 set ATEBSSID=00:11:22:33:44:55 iwpriv ra0 set ATECHANNEL=1 ; set Channel iwpriv ra0 set ATETXMODE=1 ; set TX-Mode. iwpriv ra0 set ATETXMCS=7 ; set MCS type. iwpriv ra0 set ATETXBW=0 ; set Bandwidth iwpriv ra0 set ATETXGI=0 ; set Long GI. iwpriv ra0 set ATETXLEN=1024 ; set packet length. iwpriv ra0 set ATETXPOW0=18 iwpriv ra0 set ATETXPOW1=18 iwpriv ra0 set ATETXCNT=100000 iwpriv ra0 set ATE=TXFRAME ¡K iwpriv ra0 set ATETXPOW0=19 ¡K iwpriv ra0 set ATETXPOW0=20 ¡K iwpriv ra0 set ATE=ATESTART 2.2 Check Carrier iwpriv ra0 set ATE=ATESTART iwpriv ra0 set ATECHANNEL=1 ; set Channel iwpriv ra0 set ATETXMODE=1 ; set TX-Mode. iwpriv ra0 set ATETXMCS=7 ; set MCS type. iwpriv ra0 set ATETXBW=0 ; set Bandwidth iwpriv ra0 set ATETXCNT=200 ; Tx frame count(decmial) iwpriv ra0 set ATE=TXFRAME ; Start Tx Frame(inform BBP to change, modulation mode) iwpriv ra0 set ATE=TXCARR ; Start Tx carrier, Measure carrier with instrument iwpriv ra0 set ATETXPOW0=05 iwpriv ra0 set ATETXPOW1=05 iwpriv ra0 set ATETXFREQOFFSET=19 iwpriv ra0 set ATE=ATESTART 2.3 Check specturm mask iwpriv ra0 set ATE=ATESTART iwpriv ra0 set ATECHANNEL=1 ; set Channel iwpriv ra0 set ATETXMODE=1 ; set TX-Mode. iwpriv ra0 set ATETXMCS=7 ; set MCS type. iwpriv ra0 set ATETXBW=0 ; set Bandwidth iwpriv ra0 set ATETXCNT=200 ; Tx frame count(decmial) iwpriv ra0 set ATE=TXFRAME ; Start Tx Frame(inform BBP to change, modulation mode) iwpriv ra0 set ATE=TXCONT ; Start continuous TX, Measure specturm mask with instrument iwpriv ra0 set ATETXPOW0=5 iwpriv ra0 set ATETXPOW1=5 iwpriv ra0 set ATE=ATESTART 2.4 Frequency offset tuning iwpriv ra0 set ATE=ATESTART iwpriv ra0 set ATECHANNEL=1 ; set Channel iwpriv ra0 set ATETXMODE=1 ; set TX-Mode. iwpriv ra0 set ATETXMCS=7 ; set MCS type. iwpriv ra0 set ATETXCNT=200 ; Tx frame count(decmial) iwpriv ra0 set ATETXFREQOFFSET=0 ; Set frequency offset 0(decimal) iwpriv ra0 set ATE=TXFRAME ; Start Tx Frame iwpriv ra0 set ATE=TXCARR ; Start Tx carrier, Measure carrier frequency with instrument iwpriv ra0 set ATETXFREQOFFSET=10 ; Dynamic turning frequency offset, 10(decimal) iwpriv ra0 set ATETXFREQOFFSET=20 ; Dynamic turning frequency offset, 20(decimal) iwpriv ra0 set ATE=ATESTART ; Stop, Store the tuning result to EEPROM 2.5 Rx iwpriv ra0 set ATE=ATESTART iwpriv ra0 set ATECHANNEL=1 ; set Channel iwpriv ra0 set ResetCounter=1 ; Reset statistic counter iwpriv ra0 set ATETXFREQOFFSET=value ;To use the ¡§value¡¨(decimal) you got in tx calibration iwpriv ra0 set ATETXMODE=1 ; set TX-Mode. iwpriv ra0 set ATETXMCS=7 ; set MCS type. iwpriv ra0 set ATETXBW=0 ; set Bandwidth iwpriv ra0 set ATE=RXFRAME ; Start Rx, iwpriv ra0 set ATERXFER=1 ; show RxCnt and RSSI/per-antenna, Transmit test packets iwpriv ra0 set ATE=ATESTART ; Stop iwpriv ra0 stat ; get statistics counter iwpriv ra0 set ATERXFER=1 iwpriv ra0 set ATERXANT=1 iwpriv ra0 set ATE=ATESTART iwpriv ra0 set ATERXANT=0 iwpriv ra0 set ATE=RXFRAME 2.6 Show all ate parameters iwpriv ra0 set ATESHOW=1 Mode=4 TxPower0=0 TxPower1=0 TxAntennaSel=0 RxAntennaSel=0 BBPCurrentBW=0 GI=0 MCS=7 TxMode=1 Addr1=00:11:22:aa:bb:cc Addr2=00:11:22:aa:bb:cc Addr3=00:11:22:aa:bb:cc Channel=1 TxLength=1024 TxCount=40000 TxRate=11 RFFreqOffset=0 2.7 Online help iwpriv ra0 set ATEHELP=1 ATE=ATESTART, ATESTOP, TXCONT, TXCARR, TXFRAME, RXFRAME ATEDA ATESA ATEBSSID ATECHANNEL, range:0~14(unless A band !). ATETXPOW0, set power level of antenna 1. ATETXPOW1, set power level of antenna 2. ATETXANT, set TX antenna. 0: all, 1: antenna one, 2: antenna two. ATERXANT, set RX antenna.0: all, 1: antenna one, 2: antenna two, 3: antenna three. ATETXFREQOFFSET, set frequency offset, range 0~63. ATETXBW, set BandWidth, 0:20MHz, 1:40MHz. ATETXLEN, set Frame length, range 24~2312.