BLE-CC254x-1.3.rar_BLE开发_C++ 蓝牙ble_CC2541 Bluetooth_ble蓝牙_蓝牙源码

Texas Instruments, Inc. CC2540/41 Bluetooth Low Energy Software Development Kit Release Notes ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Version 1.3 Dec 12, 2012 Notices: - This version of the Texas Instruments BLE stack and software features several changes, enhancements, and bug fixes from v1.2.1. Details of these can be found below. Changes and Enhancements: - A new sample project, SensorTag, has been added. This application runs on the CC2541 Sensor Tag board, which is included as part of the CC2541DK-SENSOR development kit. The application includes custom services for an accelerometer, barometer, gyro, humidity sensor, IR temperature sensor, and magnetometer. - A new Boot Image Manager (BIM) is included. This allows one CC2540 or CC2541 device to contain two separate software images (an "A" image and a "B" image) stored in flash. Upon power-up, the BIM selects which image to boot into. This can be based on criteria such as the state of a GPIO pin, or based on a selection from the previously running application upon reset. - A new Over-the-air firmware download (OAD) feature is included. The feature allows a peer device (which could be a central BT Smart device such as a smartphone) to push a new firmware image onto a peripheral device and update the firmware. This feature uses the BIM, in which case the downloaded image gets stored in the opposite flash location as the currently running image. For example, if the "A" image is the current image and is used to perform the download, then the downloaded image becomes the "B" image. Upon reset, the "B" image with the updated firmware would be loaded. The OAD feature optionally allows for the firmware image to be signed (using AES). Both the SensorTag and SimpleBLEPeripheral projects include configurations for using the OAD feature. A central "OADManager" application is also included, demonstrating a central implementation for sending a new firmware image to an OAD target device. - The physical HCI interface used by the network processor (HostTestRelease) has been enhanced to work while power management is enabled on the CC254x device. The UART interface, when using RTS and CTS lines, can be used by an external application processor to wake-up the CC254x network processor. When the network processor has completed all processing, it will go into deep sleep. In addition to UART, an SPI interface has been added as an option for the physical HCI interface. It also supports power management by means of the MRDY and SRDY lines. - The CC2541 configuration of the KeyFobDemo project has been modified to support the new CC2541 keyfob hardware, contained in the CC2541DK-MINI kit. The accelerometer has been changed, and a TPS62730 DC/DC converter has been added. - The structure of all projects have been changed to include a Transport Layer ("TL") library and network processor interface "NPI" source code. This new architecture allows for non-network processor applications to have slightly reduced code size by removing unnecessary stack components. - An API has been provided allowing the device name and appearance characteristics in the GAP service to be modified by the application layer. - KeyFobDemo project now includes visual feedback from LED to indicate when device has powered up and when device is advertising. - The HID-over-GATT Pofile (HOGP) implementation has been updated to now queue up HID report and send notifications upon reconnection to a HID host. - A new implementation of the HID service has been included, which supports a combined keyboard, mouse, and consumer class device in its HID report descriptor. - The API for sending L2CAP Connection Parameter Update Requests from the GAP Peripheral Role Profile has been updated to take both the requested minimum and maximum connection intervals as parameters. - BTool has been enhanced with a new GATT explorer table, displaying discovered attributes, handles, and values. An XML file is included which allows the user to define descriptions of characteristics based on their UUIDs. - HCI UART interface baud rate has been changed from 57600 to 115200. Bug Fixes: - When power management is used with long connection intervals (>2s), the CC254x remains sleeping properly without unnecessary wake-ups. - When slave latency is used, peripheral devices now properly wake-up before the next connection event when a data packet is queued - Various bug fixes on the GlucoseSensor and GlucoseCollector projects to improve compliance with profile and service specifications. - HID-over-GATT Pofile (HOGP) implementation has been updated to provide better interoperability with HID hosts. Known Issues: - Use of the NV memory (to save application data or BLE Host bonding information) during a BLE connection may cause an unexpected disconnect. The likelihood of this happening increases with frequent usage, especially when using short connection intervals. The cause is related to the NV wear algorithm which at some point may cause an NV page erase which can disrupt system real-time processing. It is therefore recommended that the NV memory be used sparingly, or only when a connection is not active. - HCI packet size of 128 bytes or more will be disregarded by the stack, and as such, no HCI event will be returned. For technical support please visit the Texas Instruments Bluetooth low energy E2E Forum: http://e2e.ti.com/support/low_power_rf/f/538.aspx ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Version 1.2.1 Apr 13, 2012 Notices: - This version of the Texas Instruments BLE stack and software is a minor update to the v1.2 release. It contains some minor enhancements and bug fixes, with no API changes or major functional changes. Changes and Enhancements: - When advertising is enabled by calling GAP_MakeDiscoverable, the first advertisement event will now occur within a few milliseconds, rather than waiting for 10ms. Bug Fixes: - The HidEmuKbd project now properly implements the HID Service include of the Battery Service. This bug fix allows for proper interoperability between the CC254x HID Profile and host systems running Windows 8. - The source code file hal_board_cfg.h has been updated to better support the serial bootloader (SBL) and Universal Bootloader (UBL). - Scanning in BTool can now be cancelled at any time without hanging or freezing the system. Known Issues: - Use of the NV memory (to save application data or BLE Host bonding information) during a BLE connection may cause an unexpected disconnect. The likelihood of this happening increases with frequent usage, especially when using short connection intervals. The cause is related to the NV wear algorithm which at some point may cause an NV page erase which can disrupt system real-time processing. It is therefore recommended that the NV memory be used sparingly, or only when a connection is not active. For technical support please visit the Texas Instruments Bluetooth low energy E2E Forum: http://e2e.ti.com/support/low_power_rf/f/538.aspx ------------------------------------------------------------------------------- ------------------------------------------------------------------------------- Version 1.2 Feb 13, 2012 Notices: - This version of the Texas Instruments BLE stack and software includes support for the CC2541, as well as some enhancements and bug fixes. Details of these can be found below. If you have not previo