欧姆龙G6K信号继电器样本.pdf

所需积分/C币:48 2019-10-09 03:37:57 307KB PDF
收藏 收藏
举报

欧姆龙G6K信号继电器样本pdf,欧姆龙G6K信号继电器选型参数介绍
G6K OmROn一 G6K Contact Ratings Load Resistive load Rated load 0.3A at 125 Vac: 1A at 30 VDc Rated carry current 1A Max switching voltage 125 VAC. 60 VDC Max switching current 1 A Characteristics tem Single-side stable models(double-pole) single-winding latching model G6K-2F. G6 K-2G. G6K-2P G6K-2F.Y. G6K-2G-Y G6KU-2 F-Y, G6KU-2G-Y, G6K-2P-Y G6KU-2P-Y Contact resistance(See note 1. )100 mQ2 max Operating(set)time(See note 2. )3 ms max (approx 1. 4 ms) 3 ms max(approx 2 ms) Release(reset)time(See note 2 )3 ms max(approx 1.3 ms) 3 ms max(approx. 1.2 ms) Insulation resistance(See note 3 )1.000 MS2 min(at 500 VDC) Dielectric Coil and contacts 1.500 VAC, 50/60 Hz for 1 min strength Contacts of different 1,000 VAC, 50/60 Hz for 1 m in polarity Contacts of same po-750 VAC, 50/60 Hz for 1 min pulse, Coiland contacts1500√(10×160us 200V(2x10,1500V10X160us withstand voltage Contacts of different 1, 500 V(10 x 160 us polarity Contacts of same po- Vibration resistance Destruction: 10 to 55 HZ. 2. 5-mm single amplitude(5-mm double amplitude)and 55 to 500 Hz, 300 m/ s(approx 30G) Malfunction: 10 to 55 HZ, 1.65-mm single amplitude(3.3-mm double amplitude)and 55 to 500 Hz, 200 m/ s(approx 20G) Shock resistance Destruction: 1,000 ms(approx. 100G) Malfunction: 750 ms(approx 75G Endurance Mechanical: 50.000, 000 operations min(at 36,000 operations/hour) Electrical: 100,000 operations min. (with a rated load at 1, 800 operations/hour) Failure rate(P level)(See note 4 )10 HA at 10 mVDC Ambient temperature Operating: -40 C to 70 C( with no icing or condensation) Ambient humidity Operating: 5% to 85% Weight Approx 0.7 g Note: The above values are initia values Note: 1. The contact resistance was measured with 10 mA at 1 VDC with a voltage-drop method 2. Values in parentheses are actual values 3. The insulation resistance was measured with a 500-vdc megohmmeter applied to the same parts as those used for checking the dielectric strength 4. This value was measured at a switching frequency of 120 operations/ min and the criterion of contact resistance is 50 Q2. This value may vary depending on the switching frequency and operating environment. Always double-check relay suitability under actual operating conditions 93 G6K ORON一 G6K Engineering Data Maximum Switching Power Ambient Temperature vs Ambient Temperature vs Maximum Coil Voltage Switching Current 己 03 0 DC resistive lo U 3 02 305070100 0507001,00 2040608100 Switching voltage(V) Ambient temperature(C) Ambient temperature(C) Note: The maximum coil voltage refers to the maxi mum value in a varying range of operating power voltage, not a continuous voltage Endurance Ambient Temperature vs Must Ambient Temperature vS Must Operate or Must Release Voltage Set or Must Reset Voltage G6K-2G(F/P), G6K-2G(F/P)-Y G6KU-2G(F/P)-Y Max, estimated value 30 VDC resistive loac Ambient temperature: 23.C o93 1.800 operations/ hour 125 VAC resistive load 5 Ambient temperature: 23'C s 3H1,8000 erations/hour Must opera:e voltage o 60-40-20 60-40-20 204c680100 Switching current (A Ambient temperature(C) Ambient temperature (C) Shock Malfunction Electrical Endurance Electrical endurance (with Must Operate and Must Re (Contact Resistance)(See note. lease Voltage)(see note. G6K-2G (F/P), G6K-2G(F/P)-Y G6K-2G(F/P). G6K-2G(F/P)-Y 600 Not Sample: GSK-2G 1c0 1,000 000 000 Shock direction 800 9o0og 国最器 Unit: m/s 2 II min 1000 Sample: G6K-2G Number of Relays: 10 X\SNNIilisaNeNXEEENSSI Zs Conditions:Shocκ Is applied in=×,±Y,and±Zd actions thrce times cach with and with out energizing the Relays to check the 000190.0 number of contact malfunction Operating frequency(x10operations) Operating frequency (x10 operations) Note: The tests were conducted at an Note: The tests were conducted at an ambient temperature of 23'C ambient temperature of 23'c G6K OmROn一 G6K Contact Reliability Test(See note. Mutual Magnetic Interference Mutual Magnetic Interference G6K-2G (F/P), G6K-2G(F/P)-Y G6K-2G(F/P), G6K-2G(F/P)-Y G6K-2G(F/P),G6K-2G(F/P)-Y Must operate vol Must release vo Must oper Must rele 0gm8= tial stage Test GEo itions: 10 mA B Switching frequency: 7,200 operations/h Sampl 5+1o ■m B-10 Not ene 5 Not energized豆s Test l T Tl TI min. 3s-20 aCCI O. 1001,cc00c0,0飢 Energized 00-30L Avcragc val Operating frequency(x10 operations) Note 1: The test was conducted at an ambient temperature of 23C 2: The contact resistance data are periodically measured reference values and are not values from each monitoring operation Contact resistance values will vary according to the switching frequency and operating environment, so be sure to check operation under the actual operating conditions before use External Magnetic Interference G6K-2G(/P),G6K-2G(F/P)-Y Average value总 Average value)o (Average value 回E回回蜀可「E +10 Sample: G6K Sample: G6K-2G Number of Relays: 10--- Must release volta Numter of Relays: 10---. Must release voltage g of Relays: 10 Must release voltage 412后1:20-80-408012厘=9a-=0-d External magnetic field(A/m)o External magnetic field(A/m)o External magnetic field(A/m) High-frequency Characteristics High-frequency Characteristics High-frequency Characteristics (Isolation) (nsertion LOss (Return Loss G6K-2G(F/P), G6K-2G(F/P)-Y G6K-2G(F/P), G6K-2G(F/P)-Y G6K-2G(F/P),G6K-2G(F/P)-Y (Average value Average valu (Average value) 10 Number of Relays: 10 Sample: G6K-2G 10 Number of Relays: 10 o.1 0.3 1.15 le: G6K-2 100 10 10 100 Frequency(MHz) Cy(MHz) Frequency(MHZ) Note: 1. The tests were conducted at an am bient temperature of 23'C 2. High-frequency characteristics depend on the PCb to which the Relay is mounted. Always check these characteristics including endurance in the actual machine before use G6K ORON一 G6K Must Operate and Must Release Must Operate and Must Release Vibration resistance Time Distribution(See note. Bounce Time Distribution(See note. G6K-2G(F/P), G6K-2G(F/P)-Y G6K-2G(FP),G6K-2G (F/P)-Y G6K-2G(F/P), G6K-2G(F/P)-Y Number of relays ust operate aa Must operate 10.0 oc8oE2 MUst release time a Must release ounce time 5.0 Must release voltage 50 N Sample: G6K-2G Nurnber of Relays Time(ms Time(ms) After test Note: The tests were conducted at an ambient temperature of 23 C Dimensions Note: All units are in millimeters unless otherwise indicated DPDT G6K-2F Mounting Dimensions(Top View) Terminal Arrangement/ Tolerance:±0.1mm Internal connections 10飞02 62 (Top View) 78 5254 Orientation mark Note: Each value has a tolerance of to 3 mm G6K-2G Mounting Dimensions (Top View) Terminal Arrangement/ Tolerance:±0.1mm Internal Connections 6.5*2 (Top View) 52 2.54 Note: Each value has a tolerance of +o 3 mm Orientalion mark G6K-2P Mounting Dimensions(Bottom view)Terminal Arrangement/ Tolerance:±0.1mm Internal Connections 652 Eight, 0.8-dia holes (Bottom view) Orientation mark 508 24254) 0.15 508 8765 Note: Each value has a tolerance of +o3 mm 【1,19) G6K亠 OmROn一 G6K G6K-2F-Y Mounting Dimensions(Top view) Terminal Arrangement/ To| erance:±0.1mm Internal Connections 10±2一 5.5t02 (Top view) 肉串帖 C 3 2】 Orientation mark Note: Each value has a tolerance of +0.3 mm G6K-2G-Y Mounting Dimensions(Top View) Terminal Arrangement/ To| erance:±0.1mm Internal connections 75 (Top view) 22 申 Orientation mark Note: Each value has a tolerance of + 0. 3 mm. Mounting Dimensions(Bottom View) Terminal Arrangement G6K-2P-Y To| erance:±0.1mm Internal connections 0±02 6.5±0 (Bottom view) 761/0.9-a.nol prier 0,4±0 5c8 12 071 Note: Each value has a tolerance of +0. 3 mm G6KU-2F-Y Mounting Dimensions(Top View) Terminal Arrangement/ Tolerance:±0.1mm Internal connections (Top View) 母斟 2外22 Note: Each value has a tolerance of to 3 mm G6KU-2G-Y Mounting Dimensions(Top view) Terminal Arrangement To| erance:±0.1mm Internal Connections 10土02 (Top View 6到- G6KU-2P-Y Note: Each value has a tolerance of to 3 mm Orientation mark Mounting Dimensions(Bottom View) Terminal Arrangement/ 10±c Tolerance to1 mm Internal connections 6-fight, 0. 8-dla holes (Bottom View) 503 【12 071 Each value has a tolerance of +o 3 mi 97 G6K ORON一 G6K Stick Packing and Tape Packing Stick Packing Relays in stick packing are arranged so that the orientation mark of each Relay in on the left side. Fifty Relays are packed on one stick Be sure not to make mistakes in Relay orientation when mounting the Relay to the PCB of ri Stopper (gray) Stopper (green) Stick length: 520 mm(stopper not included No of Relays per stick: 50 Tape Packing(Surface Mounting Terminal Models) When ordering re lays in tape packing add the prefix " -TR" to the model number, otherwise the Relays in stick packing will be pro Tape Type:ET×7200 (EIAJ(Electronic Industrial Association of Japan)) Reel type: RPM-16D(EIAJ) Relays per Reel: 900 1. Direction of Relay Insertion Pulling direction 3. Carrier Tape Dimensions GaK-2F G6K-2F-Y. G8KU-2F-Y Oricntation mark Top tape(cover tape) Illing direction Carrier tape Emboss tap分 2. Ree Dimensions G6K-2G. G6K-2G-Y. G6KU-2G-Y 2L05 175= 21.5± 15 889 75土 12土01 98 G6K亠 OmROn一 G6K Recommended Soldering Method Temperature indicate the surface temperature of the PCBs IRS Method (for surface mounting terminal mode ls) (1)IRS Method(Mounting Solder: Lead) (2)IRS Method Mounting Solder: Lead-free) Upper surtace of case (peak) 255C max Soldering 250 max Soldering 180to 200 150 Relay terminal 150 Prchcatil section 120 max 30 max Time(s) 90to120 20to30 Note: The temperature profile indicates the T ime(s) temperature of the relay termina The thickness of cream solder to be applied should be within a range between 150 and 200 un on OMRON's recommended PCB pattern In order to perform correct soldering, it is recommended that the correct soldering conditions be maintained as shown below on the left Correct Soldering Incorrect Soldering amount of Excessive solder Visually check that the Relay is properly soldered ■ Approved standards UL approval: UL1950(File No. E41515) CSA approval: C22.2 No 950(File No. LR31928 Contact form Coil rating Contact rating Number of test operations DPDT GGK-2G(F/P):3 to 12 VDC 1 A at 30 VDC 6.000 G6K(U)-2G(F/P)-Y: 3 to 24 VDC 0.5 A at 60 VDC 0.3A at 125 VAC 99 G6K ORON一 G6K Precautions Refer to page 25 for information on general precautions. Be sure to read these precautions before using the Relay. Correct Use Latching Relay Mounting Long-term Continuously ON Contacts Make sure that the vibration or shock that is generated from other Using the Relay in a circuit where the relay will be on continu devices, such as relays in operation, on the same panel and ously for long periods(without switching) can lead to unstable imposed on the Latching Relay does not exceed the rated value contacts because the heat generated by the coil itself will affect otherwise the Latching relay that has been set may be reset or the insulation, causing a film to develop on the contact surtaces vice versa. The Latching Relay is reset before shipping If exces We recommend using a latching relay(magnetic-holding relay) in sive vibration or shock is imposed, however, the Latching Relay this kind of circuit. If a single-side stable model must be used in may be set accidentally. Be sure to apply a reset signal before this kind of circuit, we recommend using a fail-safe circuit design that provides protection against contact failure or coil burnout Maximum Allowable voltage Relay Handling The maximum allowable voltage of the coil can be obtained from Use the Relay as soon as possible after opening the moisture- the coil temperature increase and the heat-resisting temperature proof package. If the Relay is left for a long time after opening the of coil insulating sheath material (EXceeding the heat-resisting moisture-proof package, the appearance may suffer and seal fail temperature may result in burning or short-circuiting. )The maxi- ure may occur after the solder mounting process. To store the mum allowable voltage also involves important restrictions which Relay after opening the moisture-proof package, place it into the include the following: original package and sealed the package with adhesive tape Must not cause thermal changes in or deterioration of the insu- When washing the product after soldering the Relay to a PcB, lating material use a water-based solvent or alcohol-based solvent, and keep the Must not cause damage to other control devices solvent temperature to less than 40C. Do not put the Relay in a Must not cause any harmful effect on people cold cleaning bath immediately after soldering · Must not cause fire Soldering Therefore, be sure to use the maximum allowable voltage beyond Soldering temperature: Approx 250 C (260c if the dWS method the value specitied in the catalog As a rule, the rated voltage must be applied to the coil. a voltage Soldering time: Approx 5 s max (approx. 2 s for the first time and exceeding the rated value, however, can be applied to the coil approx 3 s for the second time if the dws method is used) provided that the voltage is less than the maximum allowable volt Be sure to adjust the level of the molten solder so that the solder age. It must be noted that continuous voltage application to the will not overflow onto the Pcb coil will cause a coil temperature increase thus affecting charac teristics such as electrical life and resulting in the deterioration of Claw Securing Force During Automatic Mounting coil insulation During automatic insertion of Relays, make sure to set the secur- Coating ing force of each claw to the following so that the relays charac teristics will be maintained The Relay mounted on the PCB may be coated or washed but do ting or detergent containing sile wise the silicone coating or detergent may remain on the surface B of the Relay PCB Mounting If two or more Relays are closely mounted with the long sides of the Relays facing each other and soldering is performed with infrared radiation, the solder may not be properly exposed to the Direction A: 1, N irection巳: infrared rays. Be sure to keep the proper distance between adja- cent Relays as shown below Environmental Conditions During Operation, Storage, and G6K-2G Tr Protect the Relay from direct sunlight and keep the Relay und normal temperature, humidity, and If the Relay is stored for a long time in an adverse environment 2 mm min with high temperature, high humidity, organic gases, or sulfide gases, sulfide or oxide films will form on the contact surfaces These films may result in unstable contact, contact problems, or G6K-2F functional problems. Therefore, operate, store, or transport the product under specified environmental conditions 2.7 mm min Two or more Relays may be closely mounted with the short sides of the Relays facing each othe ALL DIMENSIONS SHOWN ARE IN MILLIMETERS To convert millimeters into inches, multiply by 0. 03937. To convert grams into ounces, multiply by 0.03527 Cat No. K106-E1-04

...展开详情
试读 11P 欧姆龙G6K信号继电器样本.pdf
立即下载 低至0.43元/次 身份认证VIP会员低至7折
    抢沙发
    一个资源只可评论一次,评论内容不能少于5个字
    weixin_38744435 如果觉得有用,不妨留言支持一下
    2019-10-09
    • 至尊王者

      成功上传501个资源即可获取
    关注 私信 TA的资源
    上传资源赚积分,得勋章
    最新推荐
    欧姆龙G6K信号继电器样本.pdf 48积分/C币 立即下载
    1/11
    欧姆龙G6K信号继电器样本.pdf第1页
    欧姆龙G6K信号继电器样本.pdf第2页
    欧姆龙G6K信号继电器样本.pdf第3页
    欧姆龙G6K信号继电器样本.pdf第4页

    试读已结束,剩余7页未读...

    48积分/C币 立即下载 >