r18_ap6330的步骤.txt
2017/2/9 10:47 开始整理
原始SDK默认配置为rtl8723bs，现在要修改为：AP6330。
硬件平台：全志R18。
开发板：DP-18
SDK：Android6.0.1/Linux3.10.65（v2.1版本，发布日期20161008）
WIFI测试需要支持5.8G的AP来测试。BT用普通的Android手机发送图片即可。
1、请严重注意全志R18的架构选择：ARCH=arm64
rootroot@cm-System-Product-Name:/home/wwt/dp18_ap6330/lichee/linux-3.10$
rootroot@cm-System-Product-Name:/home/wwt/dp18_ap6330/lichee/linux-3.10$ make ARCH=arm64 menuconfig
rootroot@cm-System-Product-Name:/home/wwt/dp18_ap6330/lichee/linux-3.10$
WIFI部分可以关闭realtek：
Device Drivers --->
[*] Network device support --->
[*] Wireless LAN --->
< > Realtek 8723B SDIO or SPI WiFi
< > Realtek 8723BS_VQ0 WiFi
< > Realtek 8189F SDIO WiFi
< > Realtek 8723C SDIO or SPI WiFi
可以配置内核打印级别为18（默认为17？）
General setup --->
(18) Kernel log buffer size (16 => 64KB, 17 => 128KB)
2、
Z:\home\wwt\dp18_ap6330\android\device\softwinner\tulip-d1\BoardConfig.mk
关闭这里：
# BOARD_WIFI_VENDOR := realtek
打开这里：
BOARD_WIFI_VENDOR := broadcom
蓝牙的修改：
##BOARD_HAVE_BLUETOOTH_BCM := true
BOARD_HAVE_BLUETOOTH_NAME := rtl8723bs_vq0
BOARD_HAVE_BLUETOOTH_RTK_COEX := true
BOARD_HAVE_BLUETOOTH_RTK := true
BLUETOOTH_HCI_USE_RTK_H5 := true
修改为：
BOARD_HAVE_BLUETOOTH_BCM := true
BOARD_HAVE_BLUETOOTH_NAME := ap6330
#BOARD_HAVE_BLUETOOTH_NAME := rtl8723bs_vq0
#BOARD_HAVE_BLUETOOTH_RTK_COEX := true
#BOARD_HAVE_BLUETOOTH_RTK := true
#BLUETOOTH_HCI_USE_RTK_H5 := true
3、
Z:\home\wwt\dp18_ap6330\android\device\softwinner\tulip-d1\init.sun50iw1p1.rc
蓝牙部分：
#bluesleep
insmod /system/vendor/modules/rtl_btlpm.ko
修改为：
#bluesleep
#insmod /system/vendor/modules/rtl_btlpm.ko
#network
insmod /system/vendor/modules/bcmdhd.ko
insmod /system/vendor/modules/bcm_btlpm.ko
WIFI部分：
关闭这里：
# 1. realtek & eagle wifi service
# 1.1 realtek & eagle wifi sta service
service wpa_supplicant /system/bin/wpa_supplicant \
-iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \
-I/system/etc/wifi/wpa_supplicant_overlay.conf \
-O/data/misc/wifi/sockets \
-e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0
# we will start as root and wpa_supplicant will switch to user wifi
# after setting up the capabilities required for WEXT
# user wifi
# group wifi inet keystore
class main
socket wpa_wlan0 dgram 660 wifi wifi
disabled
oneshot
# 1.2 realtek & eagle wifi sta p2p concurrent service
service p2p_supplicant /system/bin/wpa_supplicant \
-ip2p0 -Dnl80211 -c/data/misc/wifi/p2p_supplicant.conf \
-e/data/misc/wifi/entropy.bin -N \
-iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \
-I/system/etc/wifi/wpa_supplicant_overlay.conf \
-O/data/misc/wifi/sockets \
-g@android:wpa_wlan0
class main
socket wpa_wlan0 dgram 660 wifi wifi
disabled
oneshot
打开这里：
#broadcom wifi service
#1 broadcom wifi sta service
service wpa_supplicant /system/bin/wpa_supplicant \
-iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \
-I/system/etc/wifi/wpa_supplicant_overlay.conf \
-e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0
class main
socket wpa_wlan0 dgram 660 wifi wifi
disabled
oneshot
# 2 broadcom wifi sta p2p concurrent service
service p2p_supplicant /system/bin/wpa_supplicant \
-iwlan0 -Dnl80211 -c/data/misc/wifi/wpa_supplicant.conf \
-I/system/etc/wifi/p2p_supplicant_overlay.conf \
-puse_p2p_group_interface=1p2p_device=1use_multi_chan_concurrent=1 \
-m/data/misc/wifi/p2p_supplicant.conf \
-e/data/misc/wifi/entropy.bin -g@android:wpa_wlan0
class main
socket wpa_wlan0 dgram 660 wifi wifi
disabled
oneshot
4、
Z:\home\wwt\dp18_ap6330\android\device\softwinner\tulip-d1\tulip_d1.mk
PRODUCT_COPY_FILES += \
frameworks/native/data/etc/android.hardware.camera.xml:system/etc/permissions/android.hardware.camera.xml \
frameworks/native/data/etc/android.hardware.camera.front.xml:system/etc/permissions/android.hardware.camera.front.xml \
frameworks/native/data/etc/android.hardware.bluetooth.xml:system/etc/permissions/android.hardware.bluetooth.xml \
frameworks/native/data/etc/android.hardware.bluetooth_le.xml:system/etc/permissions/android.hardware.bluetooth_le.xml \
frameworks/native/data/etc/android.software.verified_boot.xml:system/etc/permissions/android.software.verified_boot.xml
frameworks/native/data/etc/android.hardware.ethernet.xml:system/etc/permissions/android.hardware.ethernet.xml
（在这里增加：）
PRODUCT_COPY_FILES += \
device/softwinner/tulip-d1/bluetooth/bt_vendor.conf:system/etc/bluetooth/bt_vendor.conf
5、2.4G/5.8G的WIFI双频段的支持：
Z:\home\wwt\dp18_ap6330\android\device\softwinner\tulip-d1\overlay\frameworks\base\core\res\res\values\config.xml
<!-- Boolean indicating whether the wifi chipset has dual frequency band support -->
<bool translatable="false" name="config_wifi_dual_band_support">false</bool>
修改为：
<!-- Boolean indicating whether the wifi chipset has dual frequency band support -->
<bool translatable="false" name="config_wifi_dual_band_support">true</bool>
6、
Z:\home\wwt\dp18_ap6330\android\device\softwinner\tulip-d1\bluetooth\vnd_tulip-d1.txt
BLUETOOTH_UART_DEVICE_PORT = "/dev/ttyS1"
FW_PATCHFILE_LOCATION = "/etc/firmware/"
UART_TARGET_BAUD_RATE = 1500000
BT_WAKE_VIA_PROC = TRUE
LPM_IDLE_TIMEOUT_MULTIPLE = 5
BTVND_DBG = TRUE
BTHW_DBG = TRUE
VNDUSERIAL_DBG = TRUE
UPIO_DBG = TRUE
SCO_PCM_IF_CLOCK_RATE = 2
修改为（最后一定要记住换一行，否则会出错）：
#Set baudrate to 1500000
UART_TARGET_BAUD_RATE=1500000
BLUETOOTH_UART_DEVICE_PORT = "/dev/ttyS1"
FW_PATCHFILE_LOCATION = "/system/vendor/modules/"
LPM_IDLE_TIMEOUT_MULTIPLE = 5
#LPM_SLEEP_MODE = FALSE
BT_WAKE_VIA_PROC = TRUE
BTVND_DBG = TRUE
BTHW_DBG = TRUE
VNDUSERIAL_DBG = TRUE
UPIO_DBG = TRUE
如果最后不换一行，编译报错：
out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/vnd_buildcfg.h:2:0: error: unterminated #ifndef
#ifndef _VND_BUILDCFG_H
^
Host Clang TableGen: llvm-rs-cc (gen-clang-comment-command-list) <= external/clang/include/clang/AST/CommentCommands.td
In file included from hardware/broadcom/libbt/include/bt_vendor_brcm.h:34:0,
from hardware/broadcom/libbt/src/upio.c:36:
out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/vnd_buildcfg.h:2:0: error: unterminated #ifndef
#ifndef _VND_BUILDCFG_H
^
In file included from hardware/broadcom/libbt/include/bt_vendor_brcm.h:34:0,
from hardware/broadcom/libbt/src/userial_vendor.c:35:
out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/vnd_buildcfg.h:2:0: error: unterminated #ifndef
#ifndef _VND_BUILDCFG_H
^
out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/vnd_buildcfg.h:12:24: error: missing binary operator before token "#"
#define UPIO_DBG TRUE#endif
^
hardware/broadcom/libbt/src/upio.c:48:6: note: in expansion of macro 'UPIO_DBG'
#if (UPIO_DBG == TRUE)
^
Host Clang TableGen: llvm-rs-cc (gen-clang-comment-nodes) <= external/clang/include/clang/Basic/CommentNodes.td
hardware/broadcom/libbt/src/upio.c: In function 'proc_btwrite_timeout':
hardware/broadcom/libbt/src/upio.c:194:47: warning: unused parameter 'arg' [-Wunused-parameter]
static void proc_btwrite_timeout(union sigval arg)
^
make: *** [out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/src/bt_vendor_brcm.o] 错误 1
make: *** 正在等待未完成的任务....
hardware/broadcom/libbt/src/userial_vendor.c: In function 'userial_vendor_ioctl':
hardware/broadcom/libbt/src/userial_vendor.c:351:63: warning: unused parameter 'p_data' [-Wunused-parameter]
void userial_vendor_ioctl(userial_vendor_ioctl_op_t op, void *p_data)
^
hardware/broadcom/libbt/src/userial_vendor.c: In function 'userial_set_port':
hardware/broadcom/libbt/src/userial_vendor.c:386:28: warning: unused parameter 'p_conf_name' [-Wunused-parameter]
int userial_set_port(char *p_conf_name, char *p_conf_value, int param)
^
hardware/broadcom/libbt/src/userial_vendor.c:386:65: warning: unused parameter 'param' [-Wunused-parameter]
int userial_set_port(char *p_conf_name, char *p_conf_value, int param)
^
In file included from hardware/broadcom/libbt/include/bt_vendor_brcm.h:34:0,
from hardware/broadcom/libbt/src/hardware.c:44:
out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/vnd_buildcfg.h:2:0: error: unterminated #ifndef
#ifndef _VND_BUILDCFG_H
^
hardware/broadcom/libbt/src/upio.c: In function 'upio_set':
hardware/broadcom/libbt/src/upio.c:360:52: warning: unused parameter 'polarity' [-Wunused-parameter]
void upio_set(uint8_t pio, uint8_t action, uint8_t polarity)
^
make: *** [out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/src/userial_vendor.o] 错误 1
Host Clang TableGen: llvm-rs-cc (gen-clang-diags-defs -clang-component=Common) <= external/clang/include/clang/Basic/Diagnostic.td
make: *** [out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/src/upio.o] 错误 1
In file included from hardware/broadcom/libbt/include/bt_vendor_brcm.h:34:0,
from hardware/broadcom/libbt/src/conf.c:32:
out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/vnd_buildcfg.h:2:0: error: unterminated #ifndef
#ifndef _VND_BUILDCFG_H
^
hardware/broadcom/libbt/src/hardware.c: In function 'hw_set_patch_file_path':
hardware/broadcom/libbt/src/hardware.c:1496:34: warning: unused parameter 'p_conf_name' [-Wunused-parameter]
int hw_set_patch_file_path(char *p_conf_name, char *p_conf_value, int param)
^
hardware/broadcom/libbt/src/hardware.c:1496:71: warning: unused parameter 'param' [-Wunused-parameter]
int hw_set_patch_file_path(char *p_conf_name, char *p_conf_value, int param)
^
hardware/broadcom/libbt/src/hardware.c: In function 'hw_set_patch_file_name':
hardware/broadcom/libbt/src/hardware.c:1514:34: warning: unused parameter 'p_conf_name' [-Wunused-parameter]
int hw_set_patch_file_name(char *p_conf_name, char *p_conf_value, int param)
^
hardware/broadcom/libbt/src/hardware.c:1514:71: warning: unused parameter 'param' [-Wunused-parameter]
int hw_set_patch_file_name(char *p_conf_name, char *p_conf_value, int param)
^
make: *** [out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/src/conf.o] 错误 1
make: *** [out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/src/hardware.o] 错误 1
#### make failed to build some targets (39:16 (mm:ss)) ####
rootroot@cm-System-Product-Name:/home/wwt/dp18_ap6330/android$
rootroot@cm-System-Product-Name:/home/wwt/dp18_ap6330/android$
rootroot@cm-System-Product-Name:/home/wwt/dp18_ap6330/android$ find . -name vnd_buildcfg.h
./hardware/realtek/bluetooth/libbt-vendor/include/vnd_buildcfg.h
./out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/vnd_buildcfg.h
./out/target/product/tulip-d1/gen/SHARED_LIBRARIES/libbt-vendor_intermediates/vnd_buildcfg.h
rootroot@cm-System-Product-Name:/home/wwt/dp18_ap6330/android$ diff hardware/realtek/bluetooth/libbt-vendor/include/vnd_buildcfg.h out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/vnd_buildcfg.h
0a1
> /* Auto-generated from device/softwinner/tulip-d1/bluetooth/vnd_tulip-d1.txt on 2017年 02月 09日 星期四 08:44:42 CST */
2a4
> #define UART_TARGET_BAUD_RATE 1500000
4c6
< #define FW_PATCHFILE_LOCATION "/etc/firmware/"
---
> #define FW_PATCHFILE_LOCATION "/system/vendor/modules/"
6c8
< #define SCO_USE_I2S_INTERFACE TRUE
---
> #define BT_WAKE_VIA_PROC TRUE
10,11c12
< #define UPIO_DBG TRUE
< #endif
---
> #define UPIO_DBG TRUE#endif
rootroot@cm-System-Product-Name:/home/wwt/dp18_ap6330/android$ cp out/target/product/tulip-d1/obj_arm/SHARED_LIBRARIES/libbt-vendor_intermediates/vnd_buildcfg.h .
rootroot@cm-System-Product-Name:/home/wwt/dp18_ap6330/android$ cp hardware/realtek/bluetooth/libbt-vendor/include/vnd_buildcfg.h h2.h
rootroot@cm-System-Product-Name:/home/wwt/dp18_ap6330/android$
7、5.7 bt_vendor.conf（请新建这个文件）
Z:\home\wwt\dp18_ap6330\android\device\softwinner\tulip-d1\bluetooth\bt_vendor.conf
# UART device port where Bluetooth controller is attached
UartPort = /dev/ttyS1
# Firmware patch file location
FwPatchFilePath = /system/vendor/modules/
#Firmware name
FwPatchFileName = bcm40183b2.hcd
8、5.8 bdroid_buildcfg.h
Z:\home\wwt\dp18_ap6330\android\device\softwinner\tulip-d1\bluetooth\bdroid_buildcfg.h
#define BTA_DM_COD {0x1A, 0x01, 0x1C}
修改为：
#define BTA_DM_COD {0x1A, 0x01, 0x14}
#define BTIF_HF_SERVICE_NAMES { BTIF_HSAG_SERVICE_NAME, NULL }
修改为：
#define BTIF_HF_SERVICE_NAMES { BTIF_HSAG_SERVICE_NAME }
9、5.9 sys_config.fex
Z:\home\wwt\dp18_ap6330\lichee\tools\pack\chips\sun50iw1p1\configs\d1\sys_config.fex
;--------------------------------------------------------------------------------
;wlan configuration
;wlan_used: 0-not use, 1- use
;wlan_busnum: sdio/usb index
;clocks: external low power clock input (32.768KHz)
;wlan_power: input supply voltage
;wlan_io_regulator: wlan/sdio I/O voltage
;wlan_regon: power up/down internal regulators used by wifi section
;wlan_hostwake: wlan to wake-up host
;--------------------------------------------------------------------------------
[wlan]
wlan_used = 1
wlan_busnum = 1
;clocks =
（根据手册增加）
wlan_power = "vcc-wifi"
wlan_io_regulator = "vcc-wifi-io"
wlan_regon = port:PL02<1><default><default><0>
wlan_hostwake = port:PL03<6><default><default><0>
;--------------------------------------------------------------------------------
;bluetooth configuration
;bt_used: 0- no used, 1- used
;clocks: external low power clock input (32.768KHz)
;bt_power: input supply voltage
;bt_io_regulator: bluetooth I/O voltage
;bt_rst_n: power up/down internal regulators used by BT section
;--------------------------------------------------------------------------------
[bt]
bt_used = 1
clocks =
（根据手册增加）
bt_power = "vcc-wifi"
bt_io_regulator = "vcc-wifi-io"
bt_rst_n = port:PL04<1><default><default><0>
可选更改：
10、
Z:\home\wwt\dp18_ap6330\lichee\tools\pack\chips\sun50iw1p1\configs\default\env.cfg
修改为：
bootdelay=3
uboot在引导进内核的时候延时3秒钟。
11、如果编译不过，可以直接在hardware中关闭realtek的编译选项：Android.mk（改名处理）
Z:\home\wwt\dp18_ap6330\android\hardware\realtek\Android_bak.mk
Z:\home\wwt\dp18_ap6330\android\hardware\realtek\bluetooth\Android.mk（改名处理）
ifeq ($(BOARD_HAVE_BLUETOOTH_RTK),true)
修改为：
ifeq ($(BOARD_HAVE_BLUETOOTH_RTK),false)
dp18_ap6330整理完工20170209_1129.7z （39个子文件） 
dp18_ap6330 
Android可以不修改这里.mk 682B
vnd_tulip-d1不换行就出错.txt 295B
bootlogo.bmp 2.93MB
