小米笔记本12.5寸二代(m3-7y30 hd615)黑苹果专用EFI文件

[V5.0.1.22] 1. Fixed. Rssi issue when close to connected AP [V5.0.1.21] 1. Fixed. Scan no ap during s3/s4/s5 or radio off/on [V5.0.1.20] 1. Fixed Disconnect, Scan no ap issue during chariot througput 2. Change Endpoint from 8 to 6. 3. Remove timer from packet complete to callback event. call directly 4. Update Firmware for MT7610U [V5.0.1.19] 1. Fixed. Clear Null frame bulk flag in correct place 2. Fixed. Data packaet has extra bytes cause bulkout issue after few hrs. [V5.0.1.18] [Interface: USB] [OS: All] [IC: 7612] [WCNCR: WCNAE00084743] [BSOD: N/A] [Customer: Edimax] 1.) [Bug][EDIMAX_EW-7722UAC V1.0A] 2pcs TX TP can't reach 866Mbps (2/100) [Solution] Call FW to do TX Shaping after both Load CR and Power on full calibration. [V5.0.1.17] [Interface: All] [OS: All] [IC: 7662] [WCNCR: WCNCR00013362] [BSOD: N/A] [Customer: N/A] 1.) [Feature] MT7662 series WDOG setting change notice [Description] http://teams.mediatek.inc/WCP/WCN/Combo/MT7662/MT7600/09_Validation/03_CSD/BBP_CR_Update/MT7662E5_BBP_CR_20140922.xls [Solution] Update 0x212c by BBP CR release MT7662E5_BBP_CR_20140922.xls [V5.0.1.16] [Interface: All] [OS: All] [IC: 7610] [WCNCR: N/A] [BSOD: N/A] [Customer: N/A] 1.) [Feature] Enables BBP Watchdog with 13ms threshold WDOG setting [Description] http://teams.mediatek.inc/sites/WHN/MT7650/MT7650_E2/60_E6/Register Programming Sequence/MT7650_MT7662_WDOG_Usage.pptx [Solution] update 0x212C by BBP CR release: MT7650E6_BBP_CR_20140922.xls. [V5.0.1.15] 1. Fixed . Null frame size is incorrect. added 4 byte padding two times 2. Added more Driver log [V5.0.1.14] [MT7610U][MT7612U] 1. [Bug] EDCCA Test Fail [Solution] Add SW EDCCA detection, turn off PA and preventing switching channel 2. [Bug] EDCCA Test Fail at ADT table. Tx will over 5ms when ESG is generating interference signal [Solution] 1.Prevent SW timer function interval is too far from 1sec 2. prevent bulkout fail to cause wkan reset 3.Prevent packet command stuck and cause wlan reset. 4. Fix dynamic VGA setting is not correct if EDCCA enabled 3. [Feature] Enhancement for EDCCA Test. EDCCASGDetected flag may be incorrect due to link down during EDCCA test [Solution] Turn off PAPE if ED signal is detected event link down 4. [Bug] DFS Fail. [Solution]1. Do LC Calibration Once when adapter is initial. Restore the LC Value for each switch channel 2. set TxRTY count as 1 when receiving switch channel announcement 3. Do TSSI adjustment only When linkup 5. [Feature] 7612 FW update. 20190918 [Modification] 1. Enable IBI watch dog (timeout from 10ms to 13 ms) 2. WOW modified for TV SQA 3. LC-Calibration backup/restore support [V5.0.1.13] [MT7612U] 1. [Feature][MT7612] WIFI MAC Initial CR Update - 140821 [Description] The update is to fixed an IOT issue found in MT7612 and MT7628 RDG test. [Solution] Update MacInitRegTable7662 by http://teams.mediatek.inc/WCP/WCN/Combo/MT7662/MT7600/09_Validation/Initial%20CR/WIFI_MAC_PBF_SEC/MT7662_E5_CR_setting_140821.xlsx [V5.0.1.12] [MT7612U][MT7610U] 1. Support set and query Country Region 2. Support DFS [V5.0.1.11] [MT7612U][MT7610U] 1. Some code does not include VHT for Phy is A Band capable Use macro as each PHY combination ex. IS_PHY_SUPPORT_5G_ONLY Remove PHY_11A check and only use RadarChannelCheck for DFS [V5.0.1.10] [MT7610U][MT7612U] 1. Support EDCCA [V5.0.1.09] [MT7612U] 1. Fixed Scan no AP after sleep long time 2. Added Following PID&VID MT7610 => ASUS PIDA711_VID7392 MT7610 => ASUS PIDB711_VID7392 MT7610 => Comcast PID293C_VID5702 MT7612 => ASUS PID180B_VID0B05 [V5.0.1.08] [MT7610U] 1. Fixed. Disconnect within 10 min while througput performance [V5.0.1.07] [MT7612U] 1. Fixed Scan no AP after Radio off/on and sleep/wakeup [V5.0.1.06] [MT7610U] 1. Fixed Ping response time is over 1000ms when Ac AP configured with 20/40/80 BW auto [V5.0.1.05] [MT7610U] 1. Bug : Low throughtput with broadcom AP Solution : Do not turn on Tx burst if ap is vbroadcom ap. 2. Add Netgear A6210 PID & VID : USB\VID_0846&PID_9053 [V5.0.1.04] [MT7612U] 1. Bug : Manual Channel setting by eFuse fail. Solution : Update NICReadEEPROMParameters about the manual channel of MT7612-EEPROM Content v0 1_04_guideline.pdf [V5.0.1.03] 1. Add calibration for MT7610U 2. MAC CR update for optimize Tx Switch Timing for 20/40/80M 3. Change copyRight info from Ralink to MediaTek Inc. 4. Fix Scan no AP Issue for MT7612U 5. Fix Scan no AP issue for MT7610U [V5.0.1.02] 1. Fixed HW PBC issue [V5.0.1.01] 1. Implement SoftAP features 2. Added OID to inform Driver terminate event to UI,SDK [V5.0.1.0] 1. MP release for MT7612U [V5.0.0.09] 1. Update Firmware 2. Update Patch_ROM Firmware [V5.0.0.08] 1. Fixed Scan no AP Issue 2. Fixed connect g mode then unable to connect A mode [V5.0.0.07] 1. Support SoftAP feature 2. Support MT7601 3. Update Firmware for MT7601. to fix after reboot Device spead is full speed instead of high speed. [V5.0.0.06] 1. Add LED Mode 2 for 7612U DNI. Expand LED Status with LED_CONNECTING and LED_CONNECTED. [V5.0.0.05] 1.Sync With Windows driver 5.1.8.122 2.Update patch FW for MT7612U [V5.0.0.04] 1. sync with windows driver 5.1.8.79 2. Fixed PerformRxDCOCCalibration7662 function [V5.0.0.03] 1. sync with windows driver 5.1.8.53 2. Update FW 3. Support 2.4G 256QAM(BW20/40) at MT7612U STA. Add new param in Registry, "2G256QAM" 4. Modify protection pate from OFDM 24M to 36M in the last condiction(sync to PCIe code) 5. Revise download FW packet size from 14k to 8k to avoud redownload fw fail. 6. New define 7612_E4 to check if it is E4 card. [V5.0.0.02] 1.sync with windows driver 5.1.8.29 [V5.0.0.01] 1.Support 7612U 2.sync with windows driver 5.0.8.5133 [V4.2.9.10] 1.Fixed : Mac STA connects to Ad-hoc on 2.4G The data rate will show only 11Mbps [V4.2.9.9] 1. Add checking for spinlock to avoid kernel panic. [V4.2.9.8] 1. Remove log print of RTMPXmitLinkSpeed. [V4.2.9.7] 1. Implement the feature of the Network Utility statistic. [V4.2.9.6] 1. Fixed the scutum cannot connect by bssid in 10.9. [V4.2.9.5] 1. Fixed WCNCR00005491. throughput of Tx does not reach standard in legacy mode. 2. Change copyright info [V4.2.9.4] 1. Fixed the free wrong size memory in MlmeFreeMemoryHandler(), it will cause kernel panic in 10.9. [V4.2.9.3] 1. Remove the patch that switchband(BW 20) in scan, Due to it is only a patch not the root cause. [V4.2.9.2] 1. fixed WCNCR00005490. Radio Off -> Radio on in Raui then nscan no AP 2. fixed WCNCR00005496. Overnight fail. scan no AP 3. fixed WCNCR00005485. IOT issue with realtek 2*2 AP. unable to connect with WPA/WPA2PSK 5Ghz. 4. fixed WCNCR00005473. Sleep -> Resume Scan no AP [V4.2.9.1] 1. fixed the hidden AP connect issue by sending seconde probe req 2. switchband(BW 20) in scan, to prevent that sometimes sta cannot recieve probe response from hidden AP when scanning. [V4.2.9.0] 1. Formal Release 2. Implement Throughput issue [V4.2.8.27] 1.) For MT7610 fixed the issue that Cold/Warm boot cannot reconize the NIC by add IOMatchCategoey property in plist file. [V4.2.8.26] 1.) Fixed WCNCR00004812.[MT7610U][sta][wifi-function][MAC]:sta ??N?AP (tkip),??N ?AP (aes)sta????N AP ?BA. [V4.2.8.25] 1.) Add case RT_OID_QUERY_HW_ARCHITECTURE_VERSION for OID query to determine if the chip is 6x9x. To fix UI get wrong tx rx rate(the transmit setting is different if the chip is 6x9x). [V4.2.8.24] 1.) Add new MT7610U PID/VID PID:17D1,VID:0B05 for ASUS. [V4.2.8.23] 1.) Set Led Off after sleep. 2.) Set Led bling when hwpbc is running. [V4.2.8.22] 1.) insert new field(ULONG Rs