===================================================================
ALi M5261 Fast Ethernet Controller SROM Programming Program v1.03
===================================================================
I. Introduction
PGSROM is a program to write data to SROM.
II. Files Description
\Psrom103\PGSROM.EXE M5261 SROM Programming Program
\Psrom103\SROM.DAT M5261 SROM Format v3.0 Data File
\Psrom103\ADDR.MAX M5261 Maximum Node ID File
\Psrom103\ADDR.LOG M5261 Programmed Node ID Log File
\Psrom103\SROM.LOG M5261 Programmed SROM Data Log File
\Psrom103\DUMP.DAT M5261 Dump/Load SROM Data File
\Psrom103\Readme.txt M5261 Read Me file
III. PGSROM Command Line Parameters
Syntax : PGSROM [/n] [/b] [/m] [/i] [/a] [/d] [/l] [/txxxxxxxxxxxx] [/h]
/n : Program SROM without WARNING Message
/b : Re-input Starting Node ID and re-create SROM data file
/m : Re-input DM9102(A) Maximum Node ID to ADDR.MAX file
/i : NO Check Increament Node ID by 1 from ADDR.LOG file
/a : Reload the EEPROM after SROM programmed OK (only for DM9102A)
/d : Dump the SROM data to DUMP.DAT file
/l : Load the SROM data from DUMP.DAT file
/txxxxxxxxxxxx : Check Trust Card Node ID (xxxxxxxxxxxx)
(The Trust Node ID must be 12 characters of 0..F)
/h : Display Help Message
(NOTICE: Between Two Parameters MUST be the SPACE character !!)
Return code :
0 : Normal Quit Code
1 : Abort Quit Code
2 : No Card Error Code
3 : Broadcast Node ID Error Code (FF FF FF FF FF FF)
4 : Beyond Max. Node ID Error Code
5 : Write SROM Error Code
6 : Null Node ID Error Code (00 00 00 00 00 00)
7 : Trust Node ID Error Code
8 : Can't read EEPROM Error Code
9 : Can't open DUMP.DAT File Error Code
IV. M5261 SROM Format v3.0 Data Description (SROM.DAT)
(Mark '*' field means that you must modify it, when you run PGSROM.EXE
at first time and no SROM.DAT file)
SubVendorID = 10 B9 ==> *Sub-System Vendor ID (10B9h)
SubDeviceID = 52 61 ==> *Sub-System Device ID (5261h)
NCE_AutoLoad = 01 AA ==> NCE and Auto_Load_Control
PCIVendorID = 10 B9 ==> PCI Vendor ID (10B9h)
PCIDeviceID = 52 61 ==> PCI Device ID (5261h)
PMCSR_PMC = 00 C4 ==> PMCSR and PMC
NodeAddress = 00 90 E6 00 00 01 ==> *Ethernet ID (0090E6000001)
STATUS_MODE = 01 ==> *PHY have Link status pin : 00 , otherwise : 01
SelectedType = 00 08 ==> Selected Connected Type (0800h)
GprControl = 80 ==> General Purpose Control (80h)
BlockCount = 06 ==> Block Count (6 Blocks)
Block0 = 8E 01 01 ==> Block0 Length, Type, *PHY Address
GPR init = 00 ==> GPR Length
PHY reset = 02 80 00 ==> Reset Sequence Length, Data
PHY info = 00 78 E0 01 00 50 00 18 ==> Block0 Other Data
Block1 = 85 80 00 20 00 40 ==> Block1 Data
Block2 = 85 00 00 00 87 00 ==> Block2 Data
Block3 = 85 00 01 00 87 00 ==> Block3 Data
Block4 = 85 00 04 00 87 00 ==> Block4 Data
Block5 = 85 00 05 00 87 00 ==> Block5 Data
V. Please follow these steps to program srom
A. Make sure the contents in SROM.DAT is correct especially the following two points.
1. NodeAddress (MAC address) :
The MAC address is composed of 6 bytes
byte6:byte5:byte4:byte3:byte2:byte1
byte6~byte4: Company ID and is depend on vendor. (ex : 00:09:E6 for ALi)
byte3~byte1: Board No, no specific rule for this except don't use the same No for different board.
2. STATUS_MODE :
STATUS_MODE = 00 (indicate that PHY in this motherboard have link status pin)
STATUS_MODE = 01 (indicate that PHY in this motherboard doesn't have link status pin)
B. Make sure the contents in ADDR.MAX is correct.
1. The upper three bytes in "M5261 MaxNodeID" is vendor specific
ex : M5261 MaxNodeID = 00 90 E6 FF FF FF (00 90 E6 : for ALi)
C. Execute the "pgsrom.exe" by the following steps.
1. Boot your PC in DOS mode.
2. Check whether these file are in your local directory:
a). pgsrom.exe
b). addr.max
c). srom.dat
3. Check informations in SROM.DAT and addr.max
a) SROM.DAT example:
NodeAddress = 00 90 E6 00 00 01 ===> Begin MAC Address
b) addr.max example:
M5261 MaxNodeID = 00 90 E6 FF FF FF ===> Maximum MAC Address
4. Run "pgsrom /i"
5. If return code is equal to zero, programming is successful.
VI. Change List
v1.03:
1. Auto reload EEPROM after the execution of pgsrom.exe.
v1.02:
1. Add "STATUS_MODE" in "Srom.dat".
ALi Corporation. (ALi) web sites:
http://www.ali.com.tw/ (Taiwan)
http://www.aliusa.com/ (America)
没有合适的资源?快使用搜索试试~ 我知道了~
网卡硬刷mac地址工具包
共324个文件
cfg:69个
bin:52个
mac:40个
4星 · 超过85%的资源 需积分: 45 110 下载量 147 浏览量
2019-03-04
20:45:49
上传
评论 11
收藏 13.04MB RAR 举报
温馨提示
支持各类主板集成网卡修改mac地址,做好dos启动盘放入使用
资源推荐
资源详情
资源评论
收起资源包目录
网卡硬刷mac地址工具包 (324个子文件)
ap5718.012 21KB
o57781c2.05 112B
o57780c2.05 96B
e57781c1.40 9KB
8168EPEF.BAK 1KB
8168FBEF.BAK 1KB
8168ELEF.BAK 1KB
8110SC.BAK 652B
E2.BAT 186B
E2.BAT 186B
EE.BAT 102B
I211.BAT 96B
X540.BAT 94B
mac.BAT 70B
1463.BAT 69B
ASRo781otp.bat 68B
PB.bat 67B
ASREEP.bat 66B
E.BAT 66B
ASR781.bat 64B
MM.BAT 64B
EE.BAT 37B
TEST.BAT 20B
073.bin 2MB
X540.bin 1.88MB
I2104MA2.bin 512KB
DPFLASH.BIN 512KB
NCSI.bin 512KB
DPFLASH.BIN 512KB
WI_NCSI.bin 512KB
DPFLASH.BIN 512KB
NOMNGID.bin 512KB
68EPSPIB.bin 512KB
Tran.bin 512KB
I2104MA2.bin 512KB
512K.bin 512KB
ad5719.bin 17KB
ad5720.bin 17KB
ad5717.bin 16KB
ad5761.bin 16KB
781EEN.BIN 12KB
cpusd.bin 11KB
cpust.bin 11KB
cpu14a.bin 9KB
cpu14b.bin 9KB
cpu05.bin 9KB
cpusc.bin 9KB
cpusj.bin 9KB
cpume.bin 9KB
cpu.bin 9KB
I218V.bin 8KB
I218LM.bin 8KB
82574_APT_A1_NoL0s_FLASH.bin 8KB
82574_NO_MNG_A1_NoL0s_FLASH.bin 8KB
CPUMEM.BIN 7KB
ump14b.bin 4KB
ump14a.bin 4KB
FLSHDGTC.BIN 3KB
flshdgsd.bin 3KB
flshdgsc.bin 3KB
flshdgsj.bin 3KB
flshdg5x.bin 3KB
flshdgst.bin 3KB
cpudiag.bin 3KB
5703.bin 3KB
flshdg05.bin 3KB
flshd14a.bin 2KB
cpudg05.bin 2KB
flshd14b.bin 2KB
FLSHDIAG.BIN 2KB
8169X.BIN 128B
8110SC.BIN 128B
ASR1463.BIN 112B
ASR.BIN 112B
OTP1466.BIN 112B
8101.CFG 5KB
39D8100.CFG 5KB
8168E.CFG 4KB
8168E.CFG 4KB
8168CP.CFG 3KB
8168CP.CFG 3KB
8168CP.CFG 3KB
8169CB.CFG 2KB
8168D.CFG 1KB
8168D.CFG 1KB
8168C.CFG 1KB
8168C.CFG 1KB
8168C.CFG 1KB
8168EEF.CFG 1KB
8168EEF.CFG 1KB
8168EPEF.CFG 1KB
8168DPEF.CFG 1KB
8168GEF.CFG 1KB
8168EPEF.CFG 1KB
8168EPEF.CFG 1KB
8168GEF.CFG 1KB
8168G.CFG 1KB
8168G.CFG 1KB
8168FBEF.CFG 1KB
8411BEF.CFG 1KB
共 324 条
- 1
- 2
- 3
- 4
资源评论
- weixin_459270902021-12-25有没有dos命令修改方法
- Ls20199992019-06-30不会用啊 怎么搞
phantomile
- 粉丝: 4
- 资源: 2
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功