x7 user manual

所需积分/C币:7 2014-08-22 15:32:45 808KB PDF
3
收藏 收藏
举报

x7 user manual
3. Lock Connection Warning: No operation when power on! (1) The system supports No LOCK and NC LOCK. For example the No LOCK (normally open at power on)is connected with ' No terminal, and the nc lock is connected with nc terminal self-inductance EMF affect the system, do not reverse the polarities preventor (2)When the Electrical Lock is connected to the access Control System, you nee (O) Share power with the lock NOLOCK ULOCK=12V, I-ILOCK 1A. NC LOCK AL+ BELL BELL I)Does not share power with the lock c12 Device does not share power ith the lock 2 V-LOCK≤1A; DC Pow INcl C. The lock is far apart from the NO LOCK BELL 11: T': device output current, ULOCK': lock voltage,'ILOCK':lock current 4.Connected with Other Parts +12V d Alarm Power Voltage output s DC 12V for Alarm Connect with Power GND DC12V nput DC 12V, 500mA (50mA standby) Positive is connected with+12V, negative onnected with 'GnD'(do not reverse the Instructions Recommended procedure Step 1: Install the device and power on Step 2: After the administrator password is authenticated and changed, register users' fingerprints, cards, or passwords Step 3: Configure access control parameters, including modifying eight passwords for opening the door and configuring the unlocking duration authentication mode, stealth mode, door status sensor mode and alarm Functions of the device 1. User Management 1.1 Administrator Operations I-8 Administrator Authentication Change Administrator Password Open the door by the Administrator Password Administrator Password Be forgotten 1.2 Add use 1-☆ Add Us Register Cards in Batch 1.3 User Authentication 1. 4 Delete Users ☆ Delete a us 2. Access Control m II-2. 1 Set/ Change Eight Passwords for Opening the Door 2.2 Configure Unlocking Duration 3 Config 2.5 Configure Door Sensor Mode 2.6 Configure Alarm Q Configure Error Operation-Triggered Alarm Alarm o Configure Alarm Delay for the door Status Sensor Operation Instructions 1. User M 1.1 Administrator Operations To ensure data security of the device, you can operate the device only after the administrator password is authenticated .Administrator Authentication 1. Press [ 2.Pes期 3. Enter the administrator (The indicator is off and M(You can authenticate the makes a long beep. The initial password is 5. Exit (Press *or do not operate 4. The authentication is the device within 20 (The indicator turns green.) ONote: The initial administrator password is 1234. You are advised to change the initial password at the beginning Change Administrator Password 1. The administrator 3. Enter a new password is authenticated (You can change the The indicator turns re YES 6. Exi 5. SuC Enter the new es a long again for authentication ONote: Four-digit passwords are automatically verified. For passwords with less than four digits press to enter the verification process Open the door by entering the Administrator Password 3. Press o (The indicator turns green turns gree and makes a long beep (The device automatically The door is opened exits the process when the K(The indicator turns green and makes a long beep. eNote: This function can be used to open the door. 4 Administrator Password Is Forgotten If the administrator password is forgotten you can press the tamper switch three times to reset the password to the initial administrator password 30 to 60 seconds after the device is disassembled from the wall or door. (There is a long beep 30 seconds after the device is disassembled from the wall or door. 1.2 Add Users Register the fingerprint or card of a user or register cards in batches ☆ Add users 1. The administrator Press 1 I password is authenticated nd makes a long beep. card once (The indicator turns and makes three beeps (Press*to exit. (The indicator turns green ONote: 1. In the registration process, the user Id increases automatically the device automatically enters the process of registering the next user when a user is successfully registered 2. The registration process fails if the fingerprint is of poor quality or the he card has b 6 green, you can register the user again Registered users must not be registered agaIn Register Cards in Batches 1. The administrator 2. Press 6 3. Swipe the first card once and makes three beeps (The device automatically 5. Cards are successfully 4. Enter the total number of registered in batches ONote: 1. In the process of entering the total number of cards, three-digit numbers are automatically verified. For numbers with less than three digits press to enter the verification process. Press to reenter the total number of 2. You must clear all the registered users before registering cards in batches. IDs of to-be- registered cards must be consecutive numbers 1.3 User Authentication Authenticate Users' Fingerprints/Cards/Passwords After the device is powered on, it enters the authentication state for users to unlock the door authe ticitie i state. H nter passwords.Yes 3 tication is (The indicator turns red and makes three beep eNote: Press after entering a password for authentication the door opens if the entered password is identical with one of the eight passwords for opening the door the initial eight passwords for opening the door are empty to change passwords for opening the door, please refer to 2.1 Set/Change eight Passwords for Opening the Door 1.4 Delete Users Delete a user whose fingerprint or card is registered or delete all users ☆Del| ete a user 2. Press 3. Enter a user ID, press the assword is authenticated E(The indicator turns green fingerprint, or swipe the and makes three beeps. 5. The user is deleted perate (The indicator turns greer 4. Determine whether the ONote: 1. In the process of entering user IDs, five-digit IDs are automatically ified. For IDs with less than five digits, press to enter the verification process 2. the device automatically enters the process of deleting the next user when a 8 user is deleted 3. The indicator turns red and makes a long beep in fifth step indicates system exits when setting successfully ☆ Delete All users 1. The administrator 2. Press 9 password is authenticated (The indicator turns green The indicator turns green and makes a long beep. and make 5.Exit (The indicator tur exits the process when the and makes a long beep, operation is completed. then turns red and makes a eNote: 1. Press 9 for automatic confirmation Other values are considered invalid. If an invalid value is entered. the device indicator turns red and the device makes a long beep and exits the process 2. The indicator turns red and makes a long beep in fourth step indicates system exits when setting successfully

...展开详情
试读 16P x7 user manual
立即下载 低至0.43元/次 身份认证VIP会员低至7折
一个资源只可评论一次,评论内容不能少于5个字
您会向同学/朋友/同事推荐我们的CSDN下载吗?
谢谢参与!您的真实评价是我们改进的动力~
上传资源赚钱or赚积分
最新推荐
x7 user manual 7积分/C币 立即下载
1/16
x7 user manual第1页
x7 user manual第2页
x7 user manual第3页
x7 user manual第4页

试读结束, 可继续读1页

7积分/C币 立即下载