/**
******************************************************************************
* @file stm32f0xx_hal_i2c.c
* @author MCD Application Team
* @brief I2C HAL module driver.
* This file provides firmware functions to manage the following
* functionalities of the Inter Integrated Circuit (I2C) peripheral:
* + Initialization and de-initialization functions
* + IO operation functions
* + Peripheral State and Errors functions
*
@verbatim
==============================================================================
##### How to use this driver #####
==============================================================================
[..]
The I2C HAL driver can be used as follows:
(#) Declare a I2C_HandleTypeDef handle structure, for example:
I2C_HandleTypeDef hi2c;
(#)Initialize the I2C low level resources by implementing the @ref HAL_I2C_MspInit() API:
(##) Enable the I2Cx interface clock
(##) I2C pins configuration
(+++) Enable the clock for the I2C GPIOs
(+++) Configure I2C pins as alternate function open-drain
(##) NVIC configuration if you need to use interrupt process
(+++) Configure the I2Cx interrupt priority
(+++) Enable the NVIC I2C IRQ Channel
(##) DMA Configuration if you need to use DMA process
(+++) Declare a DMA_HandleTypeDef handle structure for the transmit or receive channel
(+++) Enable the DMAx interface clock using
(+++) Configure the DMA handle parameters
(+++) Configure the DMA Tx or Rx channel
(+++) Associate the initialized DMA handle to the hi2c DMA Tx or Rx handle
(+++) Configure the priority and enable the NVIC for the transfer complete interrupt on
the DMA Tx or Rx channel
(#) Configure the Communication Clock Timing, Own Address1, Master Addressing mode, Dual Addressing mode,
Own Address2, Own Address2 Mask, General call and Nostretch mode in the hi2c Init structure.
(#) Initialize the I2C registers by calling the @ref HAL_I2C_Init(), configures also the low level Hardware
(GPIO, CLOCK, NVIC...etc) by calling the customized @ref HAL_I2C_MspInit(&hi2c) API.
(#) To check if target device is ready for communication, use the function @ref HAL_I2C_IsDeviceReady()
(#) For I2C IO and IO MEM operations, three operation modes are available within this driver :
*** Polling mode IO operation ***
=================================
[..]
(+) Transmit in master mode an amount of data in blocking mode using @ref HAL_I2C_Master_Transmit()
(+) Receive in master mode an amount of data in blocking mode using @ref HAL_I2C_Master_Receive()
(+) Transmit in slave mode an amount of data in blocking mode using @ref HAL_I2C_Slave_Transmit()
(+) Receive in slave mode an amount of data in blocking mode using @ref HAL_I2C_Slave_Receive()
*** Polling mode IO MEM operation ***
=====================================
[..]
(+) Write an amount of data in blocking mode to a specific memory address using @ref HAL_I2C_Mem_Write()
(+) Read an amount of data in blocking mode from a specific memory address using @ref HAL_I2C_Mem_Read()
*** Interrupt mode IO operation ***
===================================
[..]
(+) Transmit in master mode an amount of data in non-blocking mode using @ref HAL_I2C_Master_Transmit_IT()
(+) At transmission end of transfer, @ref HAL_I2C_MasterTxCpltCallback() is executed and user can
add his own code by customization of function pointer @ref HAL_I2C_MasterTxCpltCallback()
(+) Receive in master mode an amount of data in non-blocking mode using @ref HAL_I2C_Master_Receive_IT()
(+) At reception end of transfer, @ref HAL_I2C_MasterRxCpltCallback() is executed and user can
add his own code by customization of function pointer @ref HAL_I2C_MasterRxCpltCallback()
(+) Transmit in slave mode an amount of data in non-blocking mode using @ref HAL_I2C_Slave_Transmit_IT()
(+) At transmission end of transfer, @ref HAL_I2C_SlaveTxCpltCallback() is executed and user can
add his own code by customization of function pointer @ref HAL_I2C_SlaveTxCpltCallback()
(+) Receive in slave mode an amount of data in non-blocking mode using @ref HAL_I2C_Slave_Receive_IT()
(+) At reception end of transfer, @ref HAL_I2C_SlaveRxCpltCallback() is executed and user can
add his own code by customization of function pointer @ref HAL_I2C_SlaveRxCpltCallback()
(+) In case of transfer Error, @ref HAL_I2C_ErrorCallback() function is executed and user can
add his own code by customization of function pointer @ref HAL_I2C_ErrorCallback()
(+) Abort a master I2C process communication with Interrupt using @ref HAL_I2C_Master_Abort_IT()
(+) End of abort process, @ref HAL_I2C_AbortCpltCallback() is executed and user can
add his own code by customization of function pointer @ref HAL_I2C_AbortCpltCallback()
(+) Discard a slave I2C process communication using @ref __HAL_I2C_GENERATE_NACK() macro.
This action will inform Master to generate a Stop condition to discard the communication.
*** Interrupt mode or DMA mode IO sequential operation ***
==========================================================
[..]
(@) These interfaces allow to manage a sequential transfer with a repeated start condition
when a direction change during transfer
[..]
(+) A specific option field manage the different steps of a sequential transfer
(+) Option field values are defined through @ref I2C_XFEROPTIONS and are listed below:
(++) I2C_FIRST_AND_LAST_FRAME: No sequential usage, functional is same as associated interfaces in no sequential mode
(++) I2C_FIRST_FRAME: Sequential usage, this option allow to manage a sequence with start condition, address
and data to transfer without a final stop condition
(++) I2C_FIRST_AND_NEXT_FRAME: Sequential usage (Master only), this option allow to manage a sequence with start condition, address
and data to transfer without a final stop condition, an then permit a call the same master sequential interface
several times (like @ref HAL_I2C_Master_Seq_Transmit_IT() then @ref HAL_I2C_Master_Seq_Transmit_IT()
or @ref HAL_I2C_Master_Seq_Transmit_DMA() then @ref HAL_I2C_Master_Seq_Transmit_DMA())
(++) I2C_NEXT_FRAME: Sequential usage, this option allow to manage a sequence with a restart condition, address
and with new data to transfer if the direction change or manage only the new data to transfer
if no direction change and without a final stop condition in both cases
(++) I2C_LAST_FRAME: Sequential usage, this option allow to manage a sequance with a restart condition, address
and with new data to transfer if the direction change or manage only the new data to transfer
if no direction change and with a final stop condition in both cases
(++) I2C_LAST_FRAME_NO_STOP: Sequential usage (Master only), this option allow to manage a restart condition after several call of the same master sequential
interface several times (link with option I2C_FIRST_AND_NEXT_FRAME).
Usage can, transfer several bytes one by one using HAL_I2C_Master_Seq_Transmit_IT(option I2C_FIRST_AND_NEXT_FRAME then I2C_NEXT_FRAME)
or HAL_I2C_Master_Seq_Receive_IT(option I2C_FIRST_AND_
没有合适的资源?快使用搜索试试~ 我知道了~
温馨提示
STM32F0 HAL IAP 升级的嵌入式端参考代码,基于STM32CUBEIDE环境工程,以STM32F030K6T6为例,容易进行代码移植到STM32F0各系列。并另有STM32 IAP PC Software 上位机软件提供参考(https://download.csdn.net/download/hwytree/12839411)。
资源推荐
资源详情
资源评论
收起资源包目录
STM32F0 IAP Embedded Program (HAL).rar (320个子文件)
STM32F030K6T6IAP_BOOT.bin 16KB
STM32F030K6T6IAP_APP.bin 5KB
stm32f0xx_hal_i2c.c 221KB
stm32f0xx_hal_i2c.c 221KB
stm32f0xx_hal_tim.c 218KB
stm32f0xx_hal_tim.c 218KB
stm32f0xx_hal_uart.c 127KB
stm32f0xx_hal_tim_ex.c 64KB
stm32f0xx_hal_tim_ex.c 64KB
stm32f0xx_hal_rcc.c 50KB
stm32f0xx_hal_rcc.c 50KB
stm32f0xx_hal_rcc_ex.c 35KB
stm32f0xx_hal_rcc_ex.c 35KB
stm32f0xx_hal_flash_ex.c 31KB
stm32f0xx_hal_flash_ex.c 31KB
stm32f0xx_hal_dma.c 28KB
stm32f0xx_hal_dma.c 28KB
stm32f0xx_hal_flash.c 21KB
stm32f0xx_hal_flash.c 21KB
stm32f0xx_hal_gpio.c 19KB
stm32f0xx_hal_gpio.c 19KB
stm32f0xx_hal_msp.c 17KB
stm32f0xx_hal_pwr.c 17KB
stm32f0xx_hal_pwr.c 17KB
stm32f0xx_hal_uart_ex.c 16KB
stm32f0xx_hal.c 16KB
stm32f0xx_hal.c 16KB
stm32f0xx_hal_exti.c 15KB
stm32f0xx_hal_exti.c 15KB
main.c 14KB
stm32f0xx_hal_cortex.c 12KB
stm32f0xx_hal_cortex.c 12KB
stm32f0xx_hal_i2c_ex.c 10KB
stm32f0xx_hal_i2c_ex.c 10KB
system_stm32f0xx.c 10KB
system_stm32f0xx.c 10KB
stm32f0xx_hal_pwr_ex.c 9KB
stm32f0xx_hal_pwr_ex.c 9KB
main.c 6KB
stm32f0xx_it.c 5KB
stm32f0xx_it.c 4KB
sysmem.c 3KB
sysmem.c 3KB
syscalls.c 3KB
syscalls.c 3KB
stm32f0xx_hal_msp.c 2KB
usart.c 741B
.cproject 26KB
.cproject 25KB
stm32f0xx_it.d 3KB
main.d 3KB
stm32f0xx_hal_flash_ex.d 3KB
stm32f0xx_hal_uart_ex.d 3KB
stm32f0xx_hal_uart_ex.d 3KB
stm32f0xx_hal_tim_ex.d 3KB
stm32f0xx_hal_cortex.d 3KB
stm32f0xx_hal_i2c_ex.d 3KB
stm32f0xx_hal_pwr_ex.d 3KB
stm32f0xx_hal_rcc_ex.d 3KB
stm32f0xx_hal_flash.d 3KB
stm32f0xx_hal_uart.d 3KB
stm32f0xx_hal_uart.d 3KB
stm32f0xx_hal_gpio.d 3KB
stm32f0xx_hal_exti.d 3KB
stm32f0xx_hal_dma.d 3KB
stm32f0xx_hal_i2c.d 3KB
stm32f0xx_hal_pwr.d 3KB
stm32f0xx_hal_rcc.d 3KB
stm32f0xx_hal_tim.d 3KB
stm32f0xx_hal.d 3KB
stm32f0xx_hal_msp.d 3KB
usart.d 3KB
system_stm32f0xx.d 3KB
stm32f0xx_it.d 3KB
stm32f0xx_hal_flash_ex.d 3KB
stm32f0xx_hal_tim_ex.d 3KB
stm32f0xx_hal_cortex.d 3KB
stm32f0xx_hal_i2c_ex.d 3KB
stm32f0xx_hal_pwr_ex.d 3KB
stm32f0xx_hal_rcc_ex.d 3KB
stm32f0xx_hal_flash.d 3KB
stm32f0xx_hal_gpio.d 3KB
stm32f0xx_hal_exti.d 3KB
stm32f0xx_hal_dma.d 3KB
stm32f0xx_hal_i2c.d 3KB
stm32f0xx_hal_pwr.d 3KB
stm32f0xx_hal_rcc.d 3KB
stm32f0xx_hal_tim.d 3KB
stm32f0xx_hal.d 3KB
stm32f0xx_hal_msp.d 3KB
main.d 3KB
system_stm32f0xx.d 3KB
startup_stm32f030k6tx.d 83B
startup_stm32f030k6tx.d 83B
syscalls.d 45B
syscalls.d 45B
sysmem.d 41B
sysmem.d 41B
STM32F030K6T6IAP_BOOT.elf 535KB
STM32F030K6T6IAP_APP.elf 403KB
共 320 条
- 1
- 2
- 3
- 4
资源评论
- 伤感哥2022-12-17cube IDE开发的,可以打开的。
PegasusYu
- 粉丝: 1w+
- 资源: 95
上传资源 快速赚钱
- 我的内容管理 展开
- 我的资源 快来上传第一个资源
- 我的收益 登录查看自己的收益
- 我的积分 登录查看自己的积分
- 我的C币 登录后查看C币余额
- 我的收藏
- 我的下载
- 下载帮助
安全验证
文档复制为VIP权益,开通VIP直接复制
信息提交成功