k150 PIC编程器

DIYPACK_25 Dear Customer, Thankyou for purchasing a DIY Programmer. NOTE: All files mentioned in this brief are located in C:\diypgmrs This is the default installation directory for this package. PROTOCOL - > P018 %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% PLEASE NOTE 10Fxxx 18F6525 18F6621 18F8525 18F8621 ARE BETA RELEASE THESE HAVE NOT BEEN TESTED AS YET %%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%%% ----------------------------------------------------------------------- TO REMOVE OLDER SOFTWARE VERSIONS DO NOT REMOVE UNTIL YOU ARE SATISFIED THAT YOUR NEW VERSION WORKS OK. THEN JUST DELETE THE OLD PROGRAMMER DIRECTORY. YOU MAY NEED TO REASSIGN ANY DESK TOP MICROPRO ICONS TO THE NEW DIRECTORY ----------------------------------------------------------------------- ********************************************************************* ATTENTION FOR NEW DIY K128 K149-A and K149-B/C USERS ********************************************************************* To construct kit K128 please open and read through the PDF file called "K128.pdf". To construct kit K149-A please open and read through the PDF file called "K149a.pdf". To construct kit K149-B or C please open and read through the PDF file called "K149bc.pdf". Run "Micropro.exe" which is the Windows(r) interface software for this kit. ****************************************************** * PIC 16F88 MODIFCATION * * AFFECTS K128 K149'S K150 * * * * SOLDER A 10K RESISTOR BETWEEN * * PIN 9 AND PIN 10 ON THE ZIF SOCKET * ****************************************************** *************************************** OLDER HARDWARE MODIFICATION *************************************** PLEASE SEE THE FILE CALLED "RESMOD.PDF" FOR A BOARD MODIFICATION PRIOR TO USING THE BOARD. (NOT REQUIRED ON LATEST KITS) No need to read further. ********************************************************************* ATTENTION FOR OLDER DIY K128 K149-A, K149-B K150 USERS PIC16F628 UPGRADE PROCEDURE ********************************************************************* Run your OLD copy of MicroPro. Choose 16F628 from the chip selector. Look for the following files in your NEW installation directory. K128 USERS Load the file called "diyk128.hex" K149-A USERS Load the file called "diyk149a.hex" K149-B or C USERS Load the file called "diyk149bc.hex" K150 USERS Load the file called "diyk150.hex" This package has the latest MicroPro.exe file included. It's PROTOCOL number is listed above. Look down into the EEPROM section of the file listing and make sure the build number matches. DO NOT PROCEED IF THE NUMBERS DO NOT MATCH. Press PROGRAM to program the chip. When completed, close MicroPro and then turn off the programmer power. Remove the 16F628 from the IC socket on the programmer board and replace it with the newly upgraded chip making sure it is placed correctly. ****************************************************************** K149-A USERS ONLY If you haven't done so already, you must now change the 4MHz crystal (X1) to a 6MHz type. A wire link must be placed on the underside of the PCB to enable the AutoProgram feature. See page 8 of k149a.pdf. ****************************************************************** Run the NEW copy of MicroPro Turn on the programmer board. MicroPro will attempt to match itself to your programmer board type. Your upgrade is now complete. [END] Release notes and repair log v281004 MPLAB(R) start bug fixed 16F7x7 FUSE error fixed Added 12F683 v160804 Introduced K182 and K128 (ICSP) Added support for 16F5x Added support for 10Fxxx (BETA ONLY) Added support for 18F6525 6621 8525 8621 (BETA ONLY) Problem with FAST VPP/VCC fixed Removed voice overs v240604 Added [Insert Original into File] as default option Added fast power VPP1FastVCC VPP2FastVCC options v050504 Added K149C Added calibration register read Fixed File Clear bug v290304 Added various minor improvements CLK and DAT pins are outputs only during programming v100304 Repaired EEPROM data save Added EEPROM override v200204 Repaired ROM error reporting bug Enhanced help files v100204 Added support for 16F7x7 v220104 Now displays 16 bit code with byte size addresses instead of word size Repaired ID bug for 18Fxxxx Repaired FUSE and Chip ID bug for 18F819 v251103 Added voice annotations v101103 Deleted Serial EEPROM support Fixed OSCAL function v061003 Repaired 32 bit EEPROM load bug v031003 Repaired 12Cxxx calibration bug v170903 Repaired EEPROM load Changed build number to Protocol Number v090903 Repaired ICSP VPP2 bug Added hardware modification v210803 Enhanced EEPROM load Added build number to match board and MicroPro Added support for 24Cxx I2C EEPROM v300703 Fixed ICSP bug Added command line control v100703 Speeded up USB transfers Modified file load functions Added polarity function Added K149b v180603 Updated chip list Activated [FILE] -> Exit menu v030403 Included K128 documentation v280303 Repaired ID/FUSE problem v240303 Repaired file load bug Repaired 16F87x_A programming algorithm Added support for different programmer boards 4MHz crystal must be changed to 6MHz on K149-A boards Message dialogs fixed v030303 First release of new software package Peter Crowcroft DIY Electronics (HK) Ltd PO Box 88458, Sham Shui Po, Hong Kong Voice: 852-2304 2250 Fax: 852-2729 1400 Web: http://kitsrus.com Email: peterhk@kitsrus.com Number One in Electronic Kits Worldwide