zynq移植的rt2870驱动

iwpriv ================= This is detailed explanation of each parameters for iwpriv. Before reading this document, make sure you already read README. ------------------------------------------------------------------------------------------------------- USAGE: iwpriv ra0 commands val NOTE: Wireless Extension Private Handlers where [commands] [val] {range} ----------------- ------------------------------------------------- wsc_conf_mode {0, 1, 2} ::Set WPS conf mode 0: WPS Disabled 1: Enrollee 2: Registrar wsc_mode {1, 2} ::PIN or PBC 1: PIN 2: PBC wsc_pin {00000000 ~ 99999999} ::Set Enrollee's PIN Code wsc_ssid {0~z, 1~32 ascii characters} ::Set WPS AP SSID wsc_start NULL ::Trigger RT2860 STA driver to do WPS process wsc_stop NULL ::Stop WPS process wsc_gen_pincode NULL ::Generate new PIN code wsc_cred_count {1 ~ 8} ::Set count of WPS credential wsc_cred_ssid {"idx ssid_str"} ::Set SSID into credtentail[idx] idx: 0 ~ 7 ssid_str: 0~z, 1~32 ascii characters wsc_cred_auth {"idx auth_str"} ::Set AuthMode into credtentail[idx] idx: 0 ~ 7 auth_str: OPEN, WPAPSK, WPA2PSK, SHARED, WPA, WPA2 wsc_cred_encr {"idx encr_str"} ::Set EncrypType into credtentail[idx] idx: 0 ~ 7 encr_str: NONE, WEP, TKIP, AES wsc_cred_keyIdx {"idx key_index"} ::Set Key Index into credtentail[idx] idx: 0 ~ 7 key_index: 1 ~ 4 wsc_cred_key {"idx key"} ::Set Key into credtentail[idx] idx: 0 ~ 7 key: ASCII string (wep_key_len(=5,13), passphrase_len(=8~63)) OR Hex string (wep_key_len(=10,26), passphrase_len(=64)) wsc_cred_mac {"idx mac_str"} ::Set AP's MAC into credtentail[idx] idx: 0 ~ 7 mac_str: xx:xx:xx:xx:xx:xx wsc_conn_by_idx {0 ~ 7} ::Connect AP by credential index wsc_auto_conn {0, 1} ::Set driver to re-connecting to AP or not after registration. 0: Disabled, driver won't re-connect to AP with new configurations. 1: Enabled, driver will re-connect to AP with new configurations. wsc_ap_band {0, 1, 2} ::Set prefer band to do WPS with dual band WPS AP 0 : prefer 2.4G 1 : prefer 5G 2 : auto Default value is auto (2) ------------------------------------------------------------------------------------------------------- USAGE: iwpriv ra0 set [parameters]=[val] NOTE: Execute one iwpriv/set command simultaneously. where [parameters] [val] {range} ----------------- ------------------------------------------------- CountryRegion {0~7} ::Set country region 0: 1 ~ 11 ch 1: 1 ~ 13 ch 2: 10, 11 ch 3: 10 ~ 13 ch 4: 14 ch 5: 1 ~ 14 ch 6: 3 ~ 9 ch 7: 5 ~ 13 ch 31: 1 ~ 14 ch (ch1-11:active scan, ch12-14 passive scan) CountryRegionABand {0~11} ::Set country region for A band 0: 36, 40, 44, 48, 52, 56, 60, 64, 149, 153, 157, 161, 165 ch 1: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140 ch 2: 36, 40, 44, 48, 52, 56, 60, 64 ch 3: 52, 56, 60, 64, 149, 153, 157, 161 ch 4: 149, 153, 157, 161, 165 ch 5: 149, 153, 157, 161 ch 6: 36, 40, 44, 48 ch 7: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 124, 128, 132, 136, 140, 149, 153, 157, 161, 165 ch 8: 52, 56, 60, 64 ch 9: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 132, 136, 140, 149, 153, 157, 161, 165 ch 10: 36, 40, 44, 48, 149, 153, 157, 161, 165 ch 11: 36, 40, 44, 48, 52, 56, 60, 64, 100, 104, 108, 112, 116, 120, 149, 153, 157, 161 ch SSID {0~z, 1~32 ascii characters} ::Set AP SSID WirelessMode {0~10} ::Set Wireless Mode 0: legacy 11b/g mixed 1: legacy 11B only 2: legacy 11A only 3: legacy 11a/b/g mixed 4: legacy 11G only 5: 11ABGN mixed 6: 11N only 7: 11GN mixed 8: 11AN mixed 9: 11BGN mixed 10: 11AGN mixed Channel depends on CountryRegion or CountryRegionForABand ::Set Channel BGProtection {0~2} ::Set 11B/11G Protection 0:Auto, 1:Always on, 2:Always off TxPreamble {0~2} ::Set TxPreamble 0:Preamble Long, 1:Preamble Short, 2:Auto RTSThreshold {1~2347} ::Set RTS Threshold FragThreshold {256~2346} ::Set Fragment Threshold TxBurst {0,1} ::Set TxBurst Enable or Disable 0:Disable, 1:Enable NetworkType {Infra,Adhoc} ::Set Network type AuthMode {OPEN,SHARED,WEPAUTO,WPAPSK,WPA2PSK,WPANONE} ::Set Authentication Mode EncrypType {NONE,WEP,TKIP,AES} ::Set Encryption Type DefaultKeyID {1~4} ::Set Default Key ID Key1 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key1 String Key2 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key2 String Key3 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key3 String Key4 {5 ascii characters or 10 hex number or 13 ascii characters or 26 hex numbers} ::Set Key4 String WPAPSK {8~63 ascii or 64 hex characters} ::WPA Pre-Shared Key WmmCapable {0,1} ::Set WMM Capable 0:Disable WMM, 1:Enable WMM PSMode {CAM, MAX_PSP, FAST_PSP} ::Set Power Saving Mode HtBw {0,1} ::Set BandWidth 0: 20Hz 1: 40Hz HtMcs {0 ~ 15, 33} ::Set MCS 33: Auto Rate HtGi {0,1} ::Set Guard Interval(GI) 0: long GI 1: short GI HtOpMode {0,1} ::Set HT Operation Mode 0: HT mixed format 1: HT greenfield format HtExtcha {0,1} ::Set Extended Channel Switch Announcement 0: Below 1: Above HtMpduDensity {0 ~ 7} ::Set The Min