ESD测试方法和标准_esd测试方法,esd测试标准和方法资源-CSDN文库

5星 · 超过95%的资源需积分: 39 42 浏览量 2011-01-14 00:56:58 上传评论 2 收藏 364KB PDF 举报

资源详情

资源评论

资源推荐

NORME

INTERNATIONALE

CEI

IEC

INTERNATIONAL

STANDARD

61000-4-2

Edition 1.2

2001-04

Compatibilité électromagnétique (CEM) –

Partie 4-2:

Techniques d'essai et de mesure –

Essai d'immunité aux décharges électrostatiques

Electromagnetic compatibility (EMC) –

Part 4-2:

Testing and measurement techniques –

Electrostatic discharge immunity test

Numéro de référence

Reference number

CEI/IEC 61000-4-2:1995+A1:1998+A2:2000

Edition 1:1995 consolidée par les amendements 1:1998 et 2:2000

Edition 1:1995 consolidated with amendments 1:1998 and 2:2000

PUBLICATION FONDAMENTALE EN CEM

BASIC EMC PUBLICATION

61000-4-2



IEC:1995+A1:1998 – 3 –

+A2:2000

CONTENTS

Page

FOREWORD .......................................................................................................................... 5

INTRODUCTION ....................................................................................................................9

Clause

1 Scope ............................................................................................................................ 11

2 Normative references..................................................................................................... 13

3 General.......................................................................................................................... 13

4 Definitions...................................................................................................................... 13

5 Test levels ..................................................................................................................... 17

6 Test generator ...............................................................................................................19

6.1 Characteristics and performance of the ESD generator......................................... 19

6.2 Verification of the characteristics of the ESD generator......................................... 21

7 Test set-up .................................................................................................................... 23

7.1 Test set-up for tests performed in laboratories...................................................... 23

7.2 Test set-up for post-installation tests .................................................................... 29

8 Test procedure...............................................................................................................31

8.1 Laboratory reference conditions............................................................................ 31

8.2 EUT exercising ..................................................................................................... 31

8.3 Execution of the test ............................................................................................. 31

9 Evaluation of test results................................................................................................ 37

10 Test report ..................................................................................................................... 39

Annex A (informative) Explanatory notes............................................................................ 55

Annex B (informative) Constructional details ...................................................................... 65

Figure 1 – Simplified diagram of the ESD generator ............................................................. 39

Figure 2 – Example of arrangement for verification of the ESD generator............................. 41

Figure 3 – Typical waveform of the output current of the ESD generator .............................. 43

Figure 4 – Discharge electrodes of the ESD generator ......................................................... 45

Figure 5 – Example of test set-up for table-top equipment – Laboratory tests....................... 47

Figure 6 – Example of test set-up for floor-standing equipment, laboratory tests .................. 49

Figure 7 – Example of test set-up for floor-standing equipment, post-installation tests ......... 51

Figure 8 – Test set-up for ungrounded table-top equipment.................................................. 53

Figure 9 – Test set-up for ungrounded floor-standing equipment .......................................... 53

Figure A.1 – Maximum values of electrostatic voltages to which operators

may be charged while in contact with the materials mentioned in clause A.2 ........................ 63

Figures B.1 to B.7 – Construction details of the resistive load ..................................... 67 to 75

Table 1 – Test levels ............................................................................................................ 17

Table 2 – Waveform parameters........................................................................................... 21

Table A.1 – Guideline for the selection of the test levels ...................................................... 57

61000-4-2



IEC:1995+A1:1998 – 5 –

+A2:2000

INTERNATIONAL ELECTROTECHNICAL COMMISSION

____________

ELECTROMAGNETIC COMPATIBILITY (EMC) –

Part 4-2: Testing and measurement techniques –

Electrostatic discharge immunity test

FOREWORD

1) The IEC (International Electrotechnical Commission) is a worldwide organization for standardization comprising

all national electrotechnical committees (IEC National Committees). The object of the IEC is to promote

international co-operation on all questions concerning standardization in the electrical and electronic fields. To

this end and in addition to other activities, the IEC publishes International Standards. Their preparation is

entrusted to technical committees; any IEC National Committee interested in the subject dealt with may

participate in this preparatory work. International, governmental and non-governmental organizations liaising

with the IEC also participate in this preparation. The IEC collaborates closely with the International

Organization for Standardization (ISO) in accordance with conditions determined by agreement between the

two organizations.

2) The formal decisions or agreements of the IEC on technical matters express, as nearly as possible, an

international consensus of opinion on the relevant subjects since each technical committee has representation

from all interested National Committees.

3) The documents produced have the form of recommendations for international use and are published in the form

of standards, technical specifications, technical reports or guides and they are accepted by the National

Committees in that sense.

4) In order to promote international unification, IEC National Committees undertake to apply IEC International

Standards transparently to the maximum extent possible in their national and regional standards. Any

divergence between the IEC Standard and the corresponding national or regional standard shall be clearly

indicated in the latter.

5) The IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any

equipment declared to be in conformity with one of its standards.

6) Attention is drawn to the possibility that some of the elements of this International Standard may be the subject

of patent rights. The IEC shall not be held responsible for identifying any or all such patent rights.

International Standard IEC 61000-4-2 has been prepared by subcommittee 77B: High-

frequency phenomena, of IEC technical committee 77: Electromagnetic compatibility.

It forms section 2 of part 4 of IEC 61000. It has the status of a basic EMC publication in

accordance with IEC Guide 107.

It is based on the IEC 60801-2 (second edition: 1991):

Electromagnetic compatibility for

industrial process measurement and control equipment – Part 2: Electrostatic discharge

requirements,

prepared by IEC technical committee 65: Industrial-process measurement and

control.

According to a recommendation of ACEC at its meeting of December 1989, the scope of this

standard has been extended to all kinds of electrical and electronic equipment. For this

purpose it has been decided to transfer the 60801 series of publications to the 61000-4

series:

EMC testing and measurement techniques

, of technical committee 77.

剩余41页未读，继续阅读

zhanxiaohong

2013-02-28

英文版的看起来就是靠谱些。。。

评论收藏

内容反馈

ZHUZHENQIU

粉丝: 0
资源: 1

ESD测试方法和标准

评论2

最新资源

ESD测试方法和标准

评论2

ANSI ESD STM15.1-2019手套和指套的电阻测试方法【自译版本】

ESD测试标准及测试方法

ESD+测试标准

ESD模型和测试标准

ESD模型和测试标

ESD测试标准文件_IEC61000-4-2-2008

国内外ESD标准

IEC-61000-4-2 ESD静电试验方法手册

IEC-61000-4-2-ESD静电标准中文版.pdf

ESD模型和测试标准.ppt

发光二极体元件之ESD测试方法

ESD防静电相关标准

ESD模型及有关测试

手机电磁兼容测试标准及手机ESD测试要求

ESD防静电手册20.20标准.pdf

ESD S20.20中文版本标准

ESD人体模型与IEC IEC61000-4-2标准白皮书

ESD防护标准(中文版).pdf

详解ESD标准在汽车电子设计中的重要性

三份ESD中文标准.zip

9.国内外最新ESD标准.ppt

ESD标准在汽车电子设计中的重要性

了解ESD标准在汽车电子设计中的重要性

ESD最新版本标准.pdf

Qt 5实现串口调试助手 （源工程文件、0积分下载）

【SystemVerilog】路科验证V2学习笔记（全600页）.pdf

AutoSAR标准协议4.2.2

光伏-储能并网系统仿真.rar

最新资源

Qt 5实现串口调试助手（源工程文件、0积分下载）